Home » Canon Manuals » Projectors » Canon REALiS LCOS WUX6600Z » Manual Viewer

Canon REALiS LCOS WUX6600Z WUX7000Z WUX6600Z WUX5800Z Users Manual - Page 70

Installing the Lens Unit, clockwise to secure

View all Canon REALiS LCOS WUX6600Z manuals

Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Installation Procedure ■ Installing the Lens Unit 1 After confirming that the lens lever is raised, hold the lens unit with the lens connector on the left side and insert it in the projector, keeping the lens connector aligned with the connector in the projector. Connector Lens lever Lens connector Keep the lens unit level as you insert it straight into the projector. Inserting it crooked may prevent the lens lever from moving freely or make projection blurry. 2 Turn the lens lever clockwise to secure the lens unit. Lens lever • When securing the lens unit, make sure it is fully inserted in the projector, and then turn the lens lever clockwise (toward the bottom, as shown) to secure it. If it is not fully inserted, this may prevent the lens lever from moving freely or make projection blurry. • The projector stores certain information about lenses. This information must be set again when lenses are replaced. After lens replacement, lens shift reset is performed automatically when the projector is restarted. However, when reinstalling the same type of lens, perform lens shift reset manually (P158). • Also refer to instructions included with the replacement lens. 68

Section	Page
How to Use This Manual	2
Table of Contents	5
Projector Highlights	7
Safety Instructions	9
Safety Symbols in this Manual	15
Precautions for Use	16
Power Supply	16
Installation and Use	18
Hazard Distance When Equipped with a Replacement Lens (IEC 62471-5)	19
Laser Light Source	20
Remote Control Batteries	23
Handling	23
For Safe Use	25
Carrying and Installation	25
Before Installation	27
Precautions When Carrying / Shipping the Projector	27
Precautions for Installation	27
Do Not Use in the Following Environments	27
Do Not Touch the Lens with Bare Hands	28
Allow a 30 Min. Warm Up before Focus Adjustment (P48), if Possible	28
Install at a Sufficient Distance from Walls and Other Obstructions	28
Be Careful of Condensation	28
At Altitudes above 2,300 m (7,545.8'), Adjust the Settings	28
When Using Mounted on the Ceiling	29
Install Facing in the Correct Direction	29
Precautions for Portrait (Upright) Installation	30
Light Source	30
Wireless LAN (Wi-Fi)	32
Countries and Regions Where Wireless LAN Use Is Permitted	32
Model Number	32
Open Source Software	33
Before Use	34
Included Accessories	34
Projector Part Names and Functions	35
Front Side	35
Rear Side	35
Bottom Side	35
Side Control	36
LED Indicators	37
Terminals and Connectors	39
Remote Control	40
Part Names and Functions	40
Installing Remote Control Batteries	42
Remote Control Operating Range	43
Using an Optional Wired Remote (RS-RC05)	44
Basic Guide	45
Projection Procedure	46
Step 1 Connect Other Equipment	47
Step 2 Turn the Projector On	48
Step 3 Select an Input Signal	49
Step 4 Adjust the Image	50
Adjusting the Computer’s Output Resolution	50
Focusing / Resizing the Image	50
Step 5 Select the Image Quality (Image Mode)	51
Image Modes	51
Projecting an Image in the DICOM SIM Mode	52
Turn the Projector Off	53
Convenient Projection Features	54
Convenient Features	54
Temporarily Blacking Out an Image	54
Freezing the Picture	54
Projecting a Test Pattern from the Menu	55
Specifying Power-Saving Settings	55
Adjusting the Volume	56
Muting the Sound	56
Zooming Part of an Image	57
Projecting Images on a USB Flash Drive	58
Description of USB File Browser	59
Selecting an Image for Projection	61
Controlling Images in Full-Screen Projection	61
Running a Slideshow of Data Saved in a USB Flash Drive	61
Projecting Two Images Side by Side	62
Switching Input Signals	63
Installation Guide	64
Installation Procedure	65
Relationship Between Projecting Distance and Image Size	65
Installing / Removing the Lens Unit	69
Installing the Lens Unit	70
Installation	72
Tabletop or Floor Installation (Lower Than the Screen)	72
Adjusting Peripheral Focus	76
Bringing Image Edges into Focus	76
Resetting Adjustment	78
High Installation, Ceiling Mounting, and Rear Projection	79
Connection Procedure	80
Connecting Other Equipment	80
HDMI Connections	80
DVI-I Connections	81
DisplayPort Connections	81
Analog PC-2 / COMPONENT Connections	82
LAN / HDBaseT Connections	83
Audio Input/Output Connections	83
Plugging the Projector In	84
Connecting to a Network	85
Network Connection Overview	85
Connection Methods	85
Wired Networks	85
Wireless Networks	86
Network connection	87
Configuring the Computer’s Network Settings	88
Setting Up the Network	91
Error Notification Mails	97
Controlling the Projector from a Computer	99
Adjusting the Image	101
Filling the Screen	101
Selecting Screen Aspect	103
Selecting an Aspect Ratio	104
Relationship between Aspect and Screen Aspect	105
Adjusting Keystone Distortion	105
Horizontal/Vertical Keystone Correction	105
Corner Adjustment	106
Adjustment Using a Test Pattern	109
Special Arrangements	110
Projecting from Multiple Projectors at Once (Edge Blending)	110
Adjusting the Overlapping Area	112
Making Overlapping Edges Less Noticeable	114
Corner Adjustment	115
Using PC-Free Multi Projection	116
Menu Guide	120
Using Menus	121
Menu Configuration	124
Menu Description	132
Input settings	132
Aspect	133
Auto PC	133
Input signal select	133
Input signal settings	134
Input level	135
Super white	135
Color space	135
Progressive	136
Slideshow interval	136
Animation effect	136
PC-free multi projection	137
Mode setting	137
Layout pattern setting	137
Destination projector setting	137
Slideshow interval	138
Animation effect	138
Split screen	138
Input signal details	139
HDR information	140
Image adjustment	141
Image mode	142
Create profile	142
Brightness	142
Contrast	142
Sharpness	143
Gamma	143
HDR range	143
Color adjustment	143
Advanced adjustment	144
Ambient light	144
Random noise reduction	145
MPEG noise reduction	145
Mosquito noise reduction	145
Dynamic gamma	146
Contrast detail adjustment	146
Colorimetry	147
HDR (High Dynamic Range)	147
Mem. color correct	147
6-axis color adjust	148
Fine-Tune Gamma	148
Light source mode	149
Brightness level	149
Reset	150
Image priority	150
Install settings	151
Positional lock	152
Image flip H/V	152
Screen aspect	153
Zoom	153
Keystone	154
Digital image shift	154
Professional settings	154
RGB alignment	155
High altitude	156
Operating mode	156
Lens shift mode	156
Marginal focus	157
Edge blending	157
Lens - Position	160
Screen color	161
Iris	161
Test pattern	162
System settings	163
User screen settings	164
Logo capture	164
Logo position	164
No signal screen	164
Screen when blank	164
Projector on	165
On screen	165
Menu position	165
Menu display time	165
Menu rotation	166
Guide	167
Show input status	167
NMPJ standby guide display	167
Split screen ID display	167
Air filter warning display	168
Overheat warning display	168
Remote control/Side control	168
Beep	168
Key repeat	169
Key lock	169
IR receiver settings	169
Remote control channel	170
[INPUT A-C] button settings	170
[Fn] button settings	170
Audio in terminal select	171
HDBaseT signal quality	171
Extron XTP	172
Serial communication	172
Power supply settings	172
Standby power setting	173
Quick startup	173
Power management mode	173
Power management duration	174
Direct power on	174
Motion blur reduction	174
Language	175
Other settings	176
Password settings	176
Register password	177
Date and time settings	177
Schedule	178
Detailed schedule setting	179
Calibration	181
Air filter counter	182
Power counter	182
Firmware	182
Factory defaults	183
Network settings	184
Network settings lock	185
Network password setting	185
Register network password	185
Network (wired/wireless)	186
Detailed settings (wired)	187
Detailed settings (wireless)	191
PJLink	196
AMX Device Discovery	197
Crestron RoomView	197
Information	198
Checking Projector Information	199
Projector Web Screen Menu	200
Maintenance / Product Specifications / Troubleshooting	218
Maintenance	219
Cleaning the Projector	219
Replacing the Air Filter	219
Product Specifications	221
Supported Signal Types	221
Projector	223
Remote Control	225
Specification of Each Lens Unit (Option)	225
External View	227
Analog PC-2 / COMPONENT Terminal	228
Service Port (CONTROL)	228
Troubleshooting	231
LED Indicator Details	231
Symptoms and Solutions	232
You Cannot Turn on the Projector	232
You Cannot Project an Image from the Projector	233
There is no Sound	234
The Projected Image Is Blurred	234
You Cannot Project an Image Appropriately	235
The Projector Power Turns Off	235
The Projector Cannot Join the Network	236
You Cannot Operate the Remote Control	236
Index	239
Numerics	239
A	239
B	239
C	239
D	239
E	239
F	239
G	239
H	239
I	239
K	239
L	239
M	239
N	239
O	240
P	240
R	240
S	240
T	240
U	240
V	240
W	240
Z	240

Match case Limit results 1 per page

Installation Procedure

■

Installing the Lens Unit

After confirming that the lens lever is raised, hold the lens unit with the

lens connector on the left side and insert it in the projector, keeping the

lens connector aligned with the connector in the projector.

Turn the lens lever

clockwise to secure the

lens unit.

Keep the lens unit level as you insert it straight into the projector. Inserting it crooked may

prevent the lens lever from moving freely or make projection blurry.

•

When securing the lens unit, make sure it is fully inserted in the projector, and then turn

the lens lever clockwise (toward the bottom, as shown) to secure it. If it is not fully

inserted, this may prevent the lens lever from moving freely or make projection blurry.

•

The projector stores certain information about lenses. This information must be set

again when lenses are replaced.

After lens replacement, lens shift reset is performed automatically when the projector is

restarted. However, when reinstalling the same type of lens, perform lens shift reset

manually (

P158

•

Also refer to instructions included with the replacement lens.

Connector

Lens connector

Lens lever