Cisco 3845 Message Guide - Page 30

reload, show tech-support, problem persists, find out more about the error by using

Get Cisco 3845 - Security Bundle Router PDF manuals and user guides
UPC - 746320981420
View all Cisco 3845 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

GBIC_SECURITY Messages Chapter 2 Messages and Recovery Procedures Error Message GBIC_SECURITY-4-EEPROM_CRC_ERR: EEPROM checksum error for GBIC in [chars]. Explanation The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which the GBIC is inserted. Recommended Action Remove the GBIC from the port. Error Message GBIC_SECURITY-4-EEPROM_READ_ERR: Error in reading GBIC serial ID in [chars]. Explanation An error occurred while the switch was reading the GBIC type from the EEPROM. [chars] is the port in which the GBIC is inserted. Recommended Action Remove the GBIC from the port. Error Message GBIC_SECURITY-4-EEPROM_SECURITY_ERR: GBIC in [chars] failed security check. Explanation The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which the GBIC is inserted. Recommended Action Remove the GBIC from the port. Error Message GBIC_SECURITY-4-GBIC_INTERR: Internal error occurred in setup for GBIC interface [chars]. Explanation The system could not allocate resources or had some other problem during the setup for the specified SFP module interface. [chars] is the interface in which the SFP module is installed. Recommended Action Reload the switch by using the reload privileged EXEC command. If the problem persists, find out more about the error by using the show tech-support privileged EXEC command. Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to look for similar reported problems. If you still need assistance, open a case with the TAC, or provide your Cisco technical support representative with your information. For more information about these online tools and about contacting Cisco, see the "Error Message Traceback Reports" section on page 1-5. Error Message GBIC_SECURITY-6-SFP_INSERTED: Transceiver SFP [chars] module inserted in [chars] Explanation The online insertion and removal (OIR) facility detected a newly inserted transceiver module for the interface specified in the message. The first [chars] is the module, and the second [chars] is the interface. Recommended Action No action is required. 2-16 Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide OL-23408-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
2-16
Cisco ME 3400E, ME 3400, and ME 2400 Ethernet Access Switch System Message Guide
OL-23408-01
Chapter 2
Messages and Recovery Procedures
GBIC_SECURITY Messages
Error Message
GBIC_SECURITY-4-EEPROM_CRC_ERR: EEPROM checksum error for GBIC in
[chars].
Explanation
The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which
the GBIC is inserted.
Recommended Action
Remove the GBIC from the port.
Error Message
GBIC_SECURITY-4-EEPROM_READ_ERR: Error in reading GBIC serial ID in
[chars].
Explanation
An error occurred while the switch was reading the GBIC type from the EEPROM.
[chars] is the port in which the GBIC is inserted.
Recommended Action
Remove the GBIC from the port.
Error Message
GBIC_SECURITY-4-EEPROM_SECURITY_ERR: GBIC in [chars] failed security
check.
Explanation
The GBIC in the specified port has invalid EEPROM data. [chars] is the port in which
the GBIC is inserted.
Recommended Action
Remove the GBIC from the port.
Error Message
GBIC_SECURITY-4-GBIC_INTERR: Internal error occurred in setup for GBIC
interface [chars].
Explanation
The system could not allocate resources or had some other problem during the setup for
the specified SFP module interface. [chars] is the interface in which the SFP module is installed.
Recommended Action
Reload the switch by using the
reload
privileged EXEC command. If the
problem persists, find out more about the error by using the
show tech-support
privileged EXEC
command. Copy the message exactly as it appears on the console or in the system log. Research and
attempt to resolve the error by using the Output Interpreter. Use the Bug Toolkit to look for similar
reported problems. If you still need assistance, open a case with the TAC, or provide your Cisco
technical support representative with your information. For more information about these online tools
and about contacting Cisco, see the
“Error Message Traceback Reports” section on page 1-5
.
Error Message
GBIC_SECURITY-6-SFP_INSERTED: Transceiver SFP [chars] module inserted
in [chars]
Explanation
The online insertion and removal (OIR) facility detected a newly inserted transceiver
module for the interface specified in the message. The first [chars] is the module, and the second
[chars] is the interface.
Recommended Action
No action is required.