Cisco CSS11503-AC Hardware Installation Guide - Page 65

Cisco CSS11503-AC Manual

Get Cisco CSS11503-AC PDF manuals and user guides View all Cisco CSS11503-AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Chapter 2 Cabling and Troubleshooting the CSS Cabling the CSS 11503 and CSS 11506 Modules Switch Control Module Connectors and LEDs The Switch Control Module (SCM), model CSS5-SCM-2GE, provides master control and is responsible for the following functions: System powerup and boot control Centralized routing table management System-wide connection management An interface to an external Network Management Station Disk management An external RS-232 interface A CSS supports a maximum of two SCMs, one active and one passive. The Switch Control Module contains the following connectors and slots: 1 RJ-45 10-Mbps half-duplex Ethernet management connector. 1 RJ-45 RS-232 Console connector. 1 RJ-45 RS-232 Diag connector (reserved for field service diagnostic use only). 2 SFP GBICs (1000BASE-SX or LX) with LC-type connectors. Two PCMCIA slots for a hard disk or flash disk. A cover is preinstalled over the slots. Note The SCM can have a maximum of two disk drives. The SCM front panel LEDs indicate module and configuration status: • • • Two status module LEDs indicating power and module readiness Link/Act and Duplex LEDs for the Ethernet management port Link LEDs for each SFP GBIC Warning Because invisible radiation may be emitted from the aperture of the port when no fiber cable is connected, avoid exposure to radiation and do not stare into open apertures. Cisco 11500 Series Content Services Switch Hardware Installation Guide 78-13884-06 2-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
2-11
Cisco 11500 Series Content Services Switch Hardware Installation Guide
78-13884-06
Chapter 2
Cabling and Troubleshooting the CSS
Cabling the CSS 11503 and CSS 11506 Modules
Switch Control Module Connectors and LEDs
The Switch Control Module (SCM), model CSS5-SCM-2GE, provides master
control and is responsible for the following functions:
•
System powerup and boot control
•
Centralized routing table management
•
System-wide connection management
•
An interface to an external Network Management Station
•
Disk management
•
An external RS-232 interface
A CSS supports a maximum of two SCMs, one active and one passive.
The Switch Control Module contains the following connectors and slots:
•
1 RJ-45 10-Mbps half-duplex Ethernet management connector.
•
1 RJ-45 RS-232 Console connector.
•
1 RJ-45 RS-232 Diag connector (reserved for field service diagnostic use
only).
•
2 SFP GBICs (1000BASE-SX or LX) with LC-type connectors.
•
Two PCMCIA slots for a hard disk or flash disk. A cover is preinstalled over
the slots.
Note
The SCM can have a maximum of two disk drives.
The SCM front panel LEDs indicate module and configuration status:
•
Two status module LEDs indicating power and module readiness
•
Link/Act and Duplex LEDs for the Ethernet management port
•
Link LEDs for each SFP GBIC
Warning
Because invisible radiation may be emitted from the aperture of the port when
no fiber cable is connected, avoid exposure to radiation and do not stare into
open apertures.