Cisco SGE2000 Software Configuration Guide - Page 29

Disassociating a Fabric Extender From an Interface, Associating a Fabric Extender to an F2 Module

Get Cisco SGE2000 PDF manuals and user guides View all Cisco SGE2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Configuring the Fabric Extender Associating a Fabric Extender to a Fabric Interface Disassociating a Fabric Extender From an Interface Before You Begin Ensure that you have installed and enabled the Fabric Extender feature set. Ensure that you are in the correct VDC (or use the switchto vdc command). SUMMARY STEPS 1. configure terminal 2. interface {ethernet slot/port | port-channel channel} 3. no fex associate DETAILED STEPS Step 1 Step 2 Step 3 Command or Action configure terminal Example: switch# configure terminal switch(config)# interface {ethernet slot/port | port-channel channel} Example: switch(config)# interface port-channel 4 switch(config-if)# no fex associate Example: switch(config-if)# no fex associate Purpose Enters configuration mode. Specifies the interface to configure. The interface can be an Ethernet interface or a port channel. Disassociates the Fabric Extender unit attached to the interface. Associating a Fabric Extender to an F2 Module You can associate the Fabric Extender to an F2 module. Before You Begin Ensure that you have installed and enabled the Fabric Extender feature set. • switch# configure terminal • switch(config)# install feature-set fex • switch(config)# feature-set fex OL-25816-02 Cisco Nexus 2000 Series NX-OS Fabric Extender Software Configuration Guide 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Disassociating a Fabric Extender From an Interface
Before You Begin
Ensure that you have installed and enabled the Fabric Extender feature set.
Ensure that you are in the correct VDC (or use the
switchto vdc
command).
SUMMARY STEPS
1.
configure terminal
2.
interface
{
ethernet
slot
/
port
|
port-channel
channel
}
3.
no fex associate
DETAILED STEPS
Purpose
Command or Action
Enters configuration mode.
configure terminal
Example:
switch# configure terminal
switch(config)#
Step 1
Specifies the interface to configure. The interface can
be an Ethernet interface or a port channel.
interface
{
ethernet
slot
/
port
|
port-channel
channel
}
Example:
switch(config)# interface port-channel 4
switch(config-if)#
Step 2
Disassociates the Fabric Extender unit attached to the
interface.
no fex associate
Example:
switch(config-if)# no fex associate
Step 3
Associating a Fabric Extender to an F2 Module
You can associate the Fabric Extender to an F2 module.
Before You Begin
Ensure that you have installed and enabled the Fabric Extender feature set.
• switch# configure terminal
• switch(config)# install feature-set fex
• switch(config)# feature-set fex
Cisco Nexus 2000 Series NX-OS Fabric Extender Software Configuration Guide
OL-25816-02
19
Configuring the Fabric Extender
Associating a Fabric Extender to a Fabric Interface