Cisco VG224 Software Guide - Page 21

Using the setup Command, Before Starting Your Cisco VG224 - manual

Get Cisco VG224 - Analog Phone Gateway PDF manuals and user guides
UPC - 746320575360
View all Cisco VG224 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

CH A P T E R 2 Using the setup Command This chapter describes how to use the setup command facility to configure your Cisco VG224. The setup command facility prompts you to enter information needed to start a router functioning quickly. The facility steps you through a basic configuration, including LAN and WAN interfaces. This chapter presents the following major topics: • Before Starting Your Cisco VG224, page 2-1 • Using the setup Command, page 2-2 • Configuring Global Parameters, page 2-2 • Configuring Controller and Interface Parameters, page 2-5 • Completing the Configuration, page 2-6 • Where to Go Next, page 2-7 If you prefer to configure the router manually or you wish to configure a module or interface that is not included in the setup command facility, proceed to "Chapter 3, "Configuring with the Command-Line Interface," for step-by-step instructions. Before Starting Your Cisco VG224 Before you power on your Cisco VG224 and begin to use the setup command facility, make sure to follow these steps: Step 1 Step 2 Step 3 Step 4 Set up the hardware as described in the installation documents for your Cisco VG224. Configure your PC terminal emulation program for 9600 baud, 8 data bits, no parity, and 1 stop bit. Determine which network protocols you are supporting. Determine the addressing plan for each network protocol. OL-5005-01 Cisco VG224 Voice Gateway Software Configuration Guide 2-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
CHAPTER
2-1
Cisco VG224 Voice Gateway Software Configuration Guide
OL-5005-01
2
Using the setup Command
This chapter describes how to use the
setup command facility to configure your Cisco VG224. The setup
command facility prompts you to enter information needed to start a router functioning quickly. The
facility steps you through a basic configuration, including LAN and WAN interfaces.
This chapter presents the following major topics:
•
Before Starting Your Cisco VG224, page 2-1
•
Using the setup Command, page 2-2
•
Configuring Global Parameters, page 2-2
•
Configuring Controller and Interface Parameters, page 2-5
•
Completing the Configuration, page 2-6
•
Where to Go Next, page 2-7
If you prefer to configure the router manually or you wish to configure a module or interface that is not
included in the setup command facility, proceed to “
Chapter 3, “Configuring with the Command-Line
Interface,”
for step-by-step instructions.
Before Starting Your Cisco VG224
Before you power on your Cisco VG224 and begin to use the setup command facility, make sure to
follow these steps:
Step 1
Set up the hardware as described in the installation documents for your Cisco VG224.
Step 2
Configure your PC terminal emulation program for 9600 baud, 8 data bits, no parity, and 1 stop bit.
Step 3
Determine which network protocols you are supporting.
Step 4
Determine the addressing plan for each network protocol.