Cisco VG224 Software Guide - Page 24

Step 2, Return - brackets

Get Cisco VG224 - Analog Phone Gateway PDF manuals and user guides
UPC - 746320575360
View all Cisco VG224 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Configuring Global Parameters Chapter 2 Using the setup Command Step 2 Would you like to enter the initial configuration dialog? [yes/no]: yes At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. When the following message appears, enter yes to begin the initial configuration dialog: Would you like to enter the initial configuration dialog? [yes/no]: Note If you answer no to this message, you are prompted to terminate AutoInstall. AutoInstall is a procedure that configures a new Cisco VG224 based on the configuration of an existing Cisco VG224. If you terminate AutoInstall, you enter the Cisco IOS software CLI. Note The number of interfaces shown depends on the Cisco VG224. Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 When the following message appears, press Return to see the current interface summary: First, would you like to see the current interface summary? [yes]: Any interface listed with OK? value "NO" does not have a valid configuration Interface IP-Address FastEthernet0/0 unassigned OK? Method Status NO unset up Protocol down Enter a host name for the Cisco VG224: Configuring global parameters: Enter host name [Router]: VG224 The enable secret is a password used to protect access to privileged EXEC and configuration modes. This password, after entered, becomes encrypted in the configuration. Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration. Enter enable secret: xxxx The enable password is used when you do not specify an enable secret password, with some older software versions, and some boot images. Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration. Enter enable password: guessme The virtual terminal password is used to protect access to the router over a network interface. Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port: Enter virtual terminal password: guessagain Respond to the following prompts as appropriate for your network: Configure SNMP Network Management? [yes]: Cisco VG224 Voice Gateway Software Configuration Guide 2-4 OL-5005-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
2-4
Cisco VG224 Voice Gateway Software Configuration Guide
OL-5005-01
Chapter 2
Using the setup Command
Configuring Global Parameters
Would you like to enter the initial configuration dialog? [yes/no]: yes
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Step 2
When the following message appears, enter
yes
to begin the initial configuration dialog:
Would you like to enter the initial configuration dialog? [yes/no]:
Note
If you answer
no
to this message, you are prompted to terminate AutoInstall. AutoInstall is a
procedure that configures a new Cisco VG224 based on the configuration of an existing Cisco
VG224.
If you terminate AutoInstall, you enter the Cisco IOS software CLI.
Note
The number of interfaces shown depends on the Cisco VG224.
Step 3
When the following message appears, press
Return
to see the current interface summary:
First, would you like to see the current interface summary? [yes]:
Any interface listed with OK? value “NO” does not have a valid configuration
Interface
IP-Address
OK? Method Status
Protocol
FastEthernet0/0 unassigned
NO
unset
up
down
Step 4
Enter a host name for the Cisco VG224:
Configuring global parameters:
Enter host name [Router]:
VG224
The enable secret is a password used to protect access to privileged EXEC and
configuration modes. This password, after entered, becomes encrypted in the configuration.
Step 5
Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when
viewing the configuration.
Enter enable secret:
xxxx
The enable password is used when you do not specify an enable secret password, with some
older software versions, and some boot images.
Step 6
Enter an enable password that is different from the enable secret password. This password is
not
encrypted (less secure) and can be seen when viewing the configuration.
Enter enable password:
guessme
The virtual terminal password is used to protect access to the router over a network
interface.
Step 7
Enter the virtual terminal password, which prevents unauthenticated access to the router through ports
other than the console port:
Enter virtual terminal password:
guessagain
Step 8
Respond to the following prompts as appropriate for your network:
Configure SNMP Network Management? [yes]: