Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 32

Removing the Front Bezel

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Hardware Options Installation 3-3 Removing the Front Bezel To remove the front bezel: CAUTION: Before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet. 1. Follow the steps in "Shutting Down the Server" earlier in this chapter. 2. Push up on the latch at the bottom of the front bezel . 3. Swing the front bezel upward and slide it out and away from the chassis. 1 2 Figure 3-1. Removing the front bezel To replace the front bezel, reverse the above procedure. NOTE: When replacing the front bezel, make sure the top hinge points are properly placed in the chassis before rotating the front bezel back into its original position. NOTE: As a security measure, an intruder alert message will display at startup if the front bezel has been unlatched.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Hardware Options Installation
3-3
Removing the Front Bezel
To remove the front bezel:
CAUTION:
Before removing the front bezel, make sure that the server is
powered down, all cables are disconnected from the back of the server, and the
power cord is disconnected from the grounded (earthed) AC outlet.
1.
Follow the steps in “Shutting Down the Server” earlier in this chapter.
2.
Push up on the latch at the bottom of the front bezel
.
3.
Swing the front bezel
upward and slide it out and away from the
chassis.
1
2
Figure 3-1.
Removing the front bezel
To replace the front bezel, reverse the above procedure.
NOTE:
When replacing the front bezel, make sure the top hinge points are properly
placed in the chassis before rotating the front bezel back into its original position.
NOTE:
As a security measure, an intruder alert message will display at startup if the front
bezel has been unlatched.