Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 35

Removing a Drive Tray

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

3-6 Compaq ProLiant ML330 Setup and Installation Guide Removing a Drive Tray NOTE: The drive trays in the removable media bays may be used to mount internal 3.5-inch hard drives. The rails mounted inside the drive trays may be removed, and used to mount other devices in the removable media bays. To remove a drive tray from a removable media bay: CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the back of the server and the power cord is disconnected from the grounded (earthed) AC outlet. 1. Follow the steps in "Removing the Access Panel" earlier in this chapter. 2. Remove the screws on either side of the drive tray. 3. Gently slide the drive tray out of the front of the chassis. Figure 3-4. Removing the drive tray To replace a drive tray, reverse the above procedure.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
3-6
Compaq ProLiant ML330 Setup and Installation Guide
Removing a Drive Tray
NOTE:
The drive trays in the removable media bays may be used to mount internal
3.5-inch hard drives. The rails mounted inside the drive trays may be removed, and used
to mount other devices in the removable media bays.
To remove a drive tray from a removable media bay:
CAUTION:
Before removing the access panel, make sure that the server is
powered down, all cables are disconnected from the back of the server and the
power cord is disconnected from the grounded (earthed) AC outlet.
1.
Follow the steps in “Removing the Access Panel” earlier in this chapter.
2.
Remove the screws on either side of the drive tray.
3.
Gently slide the drive tray out of the front of the chassis.
Figure 3-4.
Removing the drive tray
To replace a drive tray, reverse the above procedure.