Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 37

Installing a Hard Drive

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

3-8 Compaq ProLiant ML330 Setup and Installation Guide Installing a Hard Drive To install a 3.5-inch hard drive: CAUTION: Before removing the front bezel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. 1. Follow the steps in "Removing the Access Panel" earlier in this chapter. 2. Disconnect the power and data cables from the back of all devices in the hard drive compartment. 3. Remove the three shipping screws , press the tabs on either side of the drive compartment, then pull the drive compartment from the chassis. 2 2 1 3 1 Figure 3-6. Removing the drive compartment 4. To configure the device, set the SCSI ID. You must manually set the SCSI ID on each device to a unique value in the range of 0 to 6 for each SCSI bus. Refer to the documentation provided with the device for instructions on how to set the SCSI ID. 5. Remove all terminating jumpers from third-party SCSI devices. (Compaq SCSI cables are terminated.)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
3-8
Compaq ProLiant ML330 Setup and Installation Guide
Installing a Hard Drive
To install a 3.5-inch hard drive:
CAUTION:
Before removing the front bezel, make sure that the server is
powered down, all cables are disconnected from the server, and the power cord
is disconnected from the grounded AC.
1.
Follow the steps in “Removing the Access Panel” earlier in this chapter.
2.
Disconnect the power and data cables from the back of all devices in the
hard drive compartment.
3.
Remove the three shipping screws
, press the tabs
on either side of
the drive compartment, then pull the drive compartment
from the
chassis.
1
1
2
3
2
Figure 3-6.
Removing the drive compartment
4.
To configure the device, set the SCSI ID. You must manually set the
SCSI ID on each device to a unique value in the range of 0 to 6 for each
SCSI bus. Refer to the documentation provided with the device for
instructions on how to set the SCSI ID.
5.
Remove all terminating jumpers from third-party SCSI devices.
(Compaq SCSI cables are terminated.)