Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 61

Compaq ProLiant 400 Manual

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Cabling Guidelines 4-5 Connecting an Integrated Wide-Ultra2 SCSI Controller to an Internal SCSI Hard Drive or Other SCSI Device The following steps detail the procedure for connecting cables from an integrated Wide-Ultra2 SCSI controller to an internal SCSI hard drive or other device: 1. Follow the steps in the sections following "Installation and Removal Guidelines for SCSI Hard Drives" or "Installing a Tape Drive or Other Device in a Removable Media Bay" in Chapter 3. 2. Make sure the SCSI ID is uniquely set for each device. 3. Locate the Wide-Ultra2 SCSI cable attached to the SCSI connector. 4. Install the next available connector to the hard drive or SCSI device. 5. Install the next available power connector to the hard drive or SCSI device. Figure 4-4. Cabling an integrated Wide-Ultra2 SCSI controller to a hard drive or other device

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Cabling Guidelines
4-5
Connecting an Integrated Wide-Ultra2 SCSI
Controller to an Internal SCSI Hard Drive or
Other SCSI Device
The following steps detail the procedure for connecting cables from an
integrated Wide-Ultra2 SCSI controller to an internal SCSI hard drive or other
device:
1.
Follow the steps in the sections following “Installation and Removal
Guidelines for SCSI Hard Drives” or “Installing a Tape Drive or Other
Device in a Removable Media Bay” in Chapter 3.
2.
Make sure the SCSI ID is uniquely set for each device.
3.
Locate the Wide-Ultra2 SCSI cable attached to the SCSI connector.
4.
Install the next available connector to the hard drive or SCSI device.
5.
Install the next available power connector to the hard drive or SCSI
device.
Figure 4-4.
Cabling an integrated Wide-Ultra2 SCSI controller to a hard drive
or other device