Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 44

Removing a Tape Drive or Other Device from the Removable Media Bay

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Hardware Options Installation 3-15 3. Slide the drive into the drive bay, then tighten the screws on either side of the device. Figure 3-14. Installing a tape drive 4. Connect the data and power cables to the back of the drive, as shown in Figure 3-12. 5. Remove the two bezel blanks in the front bezel in front of the tape drive. See "Removing the Bezel Blanks" earlier in this chapter. 6. Replace the access panel and the front bezel. 7. Restore power to the server. Removing a Tape Drive or Other Device from the Removable Media Bay To remove a tape drive or other device: CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. 1. Follow the steps in "Removing the Access Panel" at the beginning of this chapter.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Hardware Options Installation
3-15
3.
Slide the drive into the drive bay, then tighten the screws on either side
of the device.
Figure 3-14.
Installing a tape drive
4.
Connect the data and power cables to the back of the drive, as shown in
Figure 3-12.
5.
Remove the two bezel blanks in the front bezel in front of the tape drive.
See “Removing the Bezel Blanks” earlier in this chapter.
6.
Replace the access panel and the front bezel.
7.
Restore power to the server.
Removing a Tape Drive or Other Device from the
Removable Media Bay
To remove a tape drive or other device:
CAUTION:
Before removing the access panel, make sure that the server is
powered down, all cables are disconnected from the server, and the power cord
is disconnected from the grounded AC.
1.
Follow the steps in “Removing the Access Panel” at the beginning of
this chapter.