Compaq ProLiant 400 ProLiant ML330 Setup and Installation Guide - Page 43

CAUTION, IMPORTANT, the SCSI device ID on each device to a unique value in the range

Get Compaq ProLiant 400 PDF manuals and user guides View all Compaq ProLiant 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

3-14 Compaq ProLiant ML330 Setup and Installation Guide 5. Connect the data and power cables to the back of the device, as shown in Figure 3-12. 6. Replace the access panel and the front bezel. Restore power to the server. To install a tape drive: CAUTION: Before removing the access panel, make sure that the server is powered down, all cables are disconnected from the server, and the power cord is disconnected from the grounded AC. IMPORTANT: When installing a removable media device, remove the rails included in the drive tray and install the rails on the device, replacing any existing rails on the device. The rails are attached to the drive tray with two screws on each rail. 1. Follow the steps in "Removing the Access Panel" and "Removing the Bezel Blanks" at the beginning of this chapter. 2. To configure the device, set the SCSI device ID. You must manually set the SCSI device ID on each device to a unique value in the range of 0 to 6 for each SCSI bus. Refer to the documentation provided with the drive for instructions on how to set the SCSI device ID.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
3-14
Compaq ProLiant ML330 Setup and Installation Guide
5.
Connect the data and power cables to the back of the device, as shown
in Figure 3-12.
6.
Replace the access panel and the front bezel. Restore power to
the server.
To install a tape drive:
CAUTION:
Before removing the access panel, make sure that the server is
powered down, all cables are disconnected from the server, and the power cord
is disconnected from the grounded AC.
IMPORTANT:
When installing a removable media device, remove the rails included in the
drive tray and install the rails on the device, replacing any existing rails on the device. The
rails are attached to the drive tray with two screws on each rail.
1.
Follow the steps in “Removing the Access Panel” and “Removing the
Bezel Blanks” at the beginning of this chapter.
2.
To configure the device, set the SCSI device ID. You must manually set
the SCSI device ID on each device to a unique value in the range of
0 to 6 for each SCSI bus. Refer to the documentation provided with the
drive for instructions on how to set the SCSI device ID.