Craftsman 28913 Operation Manual - Page 19

Oil Drain Valve

Page 19 highlights

_ezclados con ol, o el uso de la humedad, y formaci6n de tto. La gasotina del combustible amientoo Para )r, se debe antes de dias o m&so le, haga arranhasta que las Jrador queden tse combustible -nacenamiento _e productos de carburador en ;s se pueden ; EL MOTOR i primera vez o del motor, se lue extra para ._stanque hasta )sici6n de oper_brague/freno y miento. en la posici6n _=sorioa la iengaged, de la aceler* _gulaci6n. _s instruccioen clima frfo y _y gire la liave tanillas del reloj art, y sueite la ]ue el motor. -_dorcontinu- iegundos por ca despu_s de va el control de :le r&pido, es! Irate de nuevoo ar, mueva el posici6n de luevo, ,,1PLADO nueva el control _n de r&pido.. ; ahora pueden _cepta esta carr para permitirle utilizando et o arriba. BATTERY Check the crankcase oil level before starting Your tractor has a battery charging system which is sufficient for normal use, However, the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick se- periodic charging of the battery with an au- curely each time you check the oil level, tomotive charger will extend its life. TO CHANGE ENGINE OIL • Keep battery and terminals clean° - Keep battery bolts tight° • Keep small vent holes open. • Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on Determine temperature range expected before oi! change° All oi! must meet API service classification SG-SL. Be sure tractor is on level surface. your tractor is maintenance free° Do not attempt to open or remove caps or covers. o Oil will drain more freely when warm. Catch oil in a suitable container. Adding or checking level of electrolyte is not necessary. TO CLEAN BATTERY AND TERMINALS Corrosion and did on the battery and terminals can cause the battery to "leak" power, 1o Disconnect BLACK battery cable first then RED battery cable and remove 1o Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil, . Remove yellow cap from end of drain valve and install the drain tube onto the fitting. battery from tractor. 2 Rinse the battery with plain water and dry, 3. Clean terminals and battery cable ends Closed and Locked Oil Drain Valve with wire brush until bright. 4. Coat terminals with grease or petroleum jelly. 5. Reinstall battery (See "REPLACING BATTERY" in the SERVICE AND AD- Yellow Cap Drain JUSTMENTS section of this manual), Tube TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if neces- 3, Unlock drain valve by pushing inward slightly and turning counterclockwise, 4. To open, pull out on the drain valve. 5o After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in sary. The belts are not adjustable. Replace the locked position as shown° belts if they begin to slip from wear: 6o Remove the drain tube and replace the ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Selectthe cap onto the end of the drain valve. 7. Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see "PRODUCT SPECIFICATIONS"section ofthis manual, oil's SAE viscosity grade according to your expected operating temperature. 8. Use gauge on oil fill cap/dipstick for checking level. For accurate reading, I tighten dipstick cap securely onto the tube before removing dipstick. Keep oil at "FULl:' line on dipstick_ Tighten cap onto the tube securely when finished. TEMPERATURE RAttGE ANTICIPATED BEFORE NS,_T OIL CHANG_ NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, the oils will result in increased oil consum ption when used above 32°R Check your engine oil level more frequently to avoid possible engine damage from running low on oil Change the oil after every 50 hours of opera- tion or at least once a year if the tractor is not used for 50 hours in one year, 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64

_ezclados con
ol, o el uso de
la
humedad,
y formaci6n de
tto. La gasotina
del combustible
amientoo Para
)r, se debe
antes de
dias o m&so
le, haga arran-
hasta que las
Jrador queden
tse combustible
-nacenamiento
_e productos de
carburador
en
;s se pueden
; EL MOTOR
i primera vez o
del motor, se
lue extra para
._stanque hasta
)sici6n de oper-
_brague/freno y
miento.
en la posici6n
_=sorioa la
iengaged,
de la aceler*
_gulaci6n.
_s instruccio-
en clima frfo y
_y gire la liave
tanillas del reloj
art, y sueite
la
]ue el motor.
-_dorcontinu-
iegundos por
ca despu_s de
va el control de
:le r&pido, es-
! Irate de nuevoo
ar, mueva el
posici6n de
luevo,
,,1PLADO
nueva el control
_n de r&pido..
; ahora pueden
_cepta esta car-
r para permitirle
utilizando et
o arriba.
BATTERY
Your
tractor
has a battery
charging
system
which
is sufficient
for normal
use,
However,
periodic
charging
of the battery
with
an au-
tomotive
charger
will
extend
its life.
Keep
battery
and
terminals
clean°
-
Keep
battery
bolts tight°
Keep
small
vent
holes
open.
Recharge
at
6-10
amperes
for
1 hour.
NOTE:
The
original
equipment
battery
on
your
tractor
is
maintenance
free°
Do
not
attempt
to open
or remove
caps
or covers.
Adding
or
checking
level
of
electrolyte
is
not necessary.
TO
CLEAN
BATTERY
AND
TERMINALS
Corrosion
and
did on the battery
and termi-
nals
can cause
the battery
to "leak"
power,
1o
Disconnect
BLACK
battery
cable
first
then
RED
battery
cable
and
remove
battery
from
tractor.
2
Rinse
the
battery
with
plain
water
and
dry,
3.
Clean
terminals
and
battery
cable
ends
with
wire
brush
until
bright.
4.
Coat terminals
with grease
or petroleum
jelly.
5.
Reinstall
battery
(See
"REPLACING
BATTERY"
in the
SERVICE
AND
AD-
JUSTMENTS
section
of this
manual),
TRANSAXLE
COOLING
Keep transaxle
free from
build-up
of dirt and
chaff which
can restrict
cooling.
V-BELTS
Check
V-belts for deterioration
and wear after
100 hours
of operation
and replace
if neces-
sary.
The
belts
are not adjustable.
Replace
belts
if they
begin
to slip from
wear:
ENGINE
LUBRICATION
Only use high quality
detergent
oil rated with
API service
classification
SG-SL.
Selectthe
oil's
SAE
viscosity
grade
according
to your
expected
operating
temperature.
I
TEMPERATURE
RAttGE ANTICIPATED
BEFORE NS,_T OIL CHANG_
NOTE:
Although
multi-viscosity
oils (5W30,
10W30
etc.) improve
starting
in cold weather,
the oils will result in increased
oil consum ption
when
used above
32°R
Check
your
engine
oil
level
more
frequently
to avoid
possible
engine
damage
from
running
low on oil
Change
the oil after every 50 hours of opera-
tion
or at least
once
a year
if the tractor
is
not used for
50 hours
in one year,
19
Check
the crankcase
oil level
before starting
the engine
and after
each eight
(8) hours
of
operation.
Tighten
oil fill
cap/dipstick
se-
curely
each time
you
check
the oil level,
TO
CHANGE
ENGINE
OIL
Determine
temperature
range
expected
before
oi!
change°
All
oi!
must
meet
API
service
classification
SG-SL.
o
1o
.
Be sure
tractor
is on level
surface.
Oil will drain
more
freely
when
warm.
Catch
oil in a suitable
container.
Remove
oil fill cap/dipstick.
Be careful
not to allow
dirt to enter the engine
when
changing
oil,
Remove
yellow
cap
from
end
of drain
valve
and
install
the drain
tube
onto the
fitting.
Oil Drain Valve
Closed and
Locked
Yellow
Cap
Drain
Tube
3,
Unlock
drain
valve
by
pushing
inward
slightly
and
turning
counterclockwise,
4.
To open,
pull out on the drain valve.
5o After oil has drained
completely,
close and
lock
the
drain
valve
by
pushing
inward
and
turning
clockwise
until
the
pin is in
the locked
position
as shown°
6o
Remove
the drain
tube
and
replace
the
cap
onto the end of the drain
valve.
7.
Refill engine
with oil through
oil fill dipstick
tube.
Pour
slowly.
Do not overfill.
For
approximate
capacity
see
"PRODUCT
SPECIFICATIONS"section
ofthis manual,
8.
Use
gauge
on
oil
fill
cap/dipstick
for
checking
level.
For
accurate
reading,
tighten
dipstick
cap
securely
onto
the
tube
before
removing
dipstick.
Keep
oil
at
"FULl:'
line
on dipstick_
Tighten
cap
onto the tube securely
when
finished.