Craftsman 28913 Operation Manual - Page 24

Ela Caja

Get Craftsman 28913 - LTS 1500 17.5 HP/42inch Lawn Tractor PDF manuals and user guides View all Craftsman 28913 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

TRANSAXLE GEAR SHIFT LEVER NEUTRAL ADJUSTMENT The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows: 1. Make sure transaxle is in neutral (N)o NOTE: When the tractor rear wheels move freely, the transaxle is in neutral° 2. Loosen adjustment bolt in front of the right rear wheel. 3. Position the gear shift lever in the neutral (N) position. 4. Tighten adjustment bolt securely. NOTE: If additiona! clearance is needed to get to adjustment bolt, move mower deck height to the lowest position° Gearshift Neutral Lock Gate TO REMOVE WHEEL FOR REPAIRS 1_ Block up axle securely_ 2. Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose), 3, Repair tire and reassemble. NOTE: On rear wheels only: align grooves in rear wheel hub and axle, Insert square key. 4. Replace washers and snap retaining ring securely in axle groove, 5. Replace axle coven NOTE: To seal tire punctures and prevent flat tires due to stow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion. Washers Retaining Ring ,\ Axle \ / _-"-:, I Adjustment Bolt TO ADJUST STEERING WHEEL ALIGNMENT tfsteering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steering wheel and reassemble with crossbars horizontal. Tighten securely° FRONT WHEEL TOE-IN/CAMBER The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact a Sears or other qualified service center. | Square Key (Rear Wheel Only) TO START ENGINE WITH A WEAK BATTERY _WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from batteries, Always wear eye protection when around batteries. If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE section of this manual), If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: "-four tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles. TO A'I-FACH JUMPER CABLES - 1. Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(AB), taking care not to short against tractor chassis. 2. Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery. 3. Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery. 24 REVISION E LLANTAS Las llantas en masiado en la presi6n de fas para obtener . Reduzca la REVISION [:, CONJUNTO Para obtener t la caja de la sl en la forma ac LA CAJA DE 1 Servicio y Aju.' REVISION E DA DE TOD Vea las figura., las correas de segadora y de Servicio y Aju, las correas si_ REV1SION E Una vez que L jar su tractor, correctamente FUNCtONA B servicio y ajus

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
TRANSAXLE
GEAR
SHIFT
LEVER
NEU-
TRAL
ADJUSTMENT
The
transaxle
should
be in neutral
when the
gear
shift
lever
is in neutral
(N)
(lock
gate)
position.
The
adjustment
is
preset
at
the
factory;
however,
if adjustment
is needed,
proceed
as follows:
1.
Make
sure
transaxle
is in neutral
(N)o
NOTE:
When
the tractor
rear wheels
move
freely,
the transaxle
is in neutral°
2.
Loosen
adjustment
bolt
in front
of
the
right
rear wheel.
3.
Position
the gear shift lever
in the neutral
(N) position.
4.
Tighten
adjustment
bolt securely.
NOTE:
If additiona!
clearance
is needed
to
get to
adjustment
bolt,
move
mower
deck
height
to the lowest
position°
Neutral Lock Gate
Gearshift
/
_-":
-,
I
Adjustment
Bolt
TO ADJUST
STEERING
WHEEL
ALIGN-
MENT
tfsteering
wheel crossbars
are not horizontal
(left
to
right)
when
wheels
are
positioned
straight
forward,
remove
steering
wheel
and
reassemble
with
crossbars
horizontal.
Tighten
securely°
FRONT
WHEEL
TOE-IN/CAMBER
The
front
wheel
toe-in
and camber
are not
adjustable
on your
tractor.
If damage
has
occurred
to affect
the front
wheel
toe-in
or
camber,
contact
a Sears
or other
qualified
service
center.
TO
REMOVE
WHEEL
FOR
REPAIRS
1_ Block
up axle
securely_
2.
Remove
axle
cover,
retaining
ring and
washers
to allow
wheel
removal
(rear
wheels
have
a square
key - Do
not
lose),
3,
Repair
tire and
reassemble.
NOTE:
On rear
wheels
only:
align
grooves
in rear wheel
hub and
axle,
Insert
square
key.
4.
Replace
washers
and
snap
retaining
ring securely
in axle
groove,
5.
Replace
axle
coven
NOTE:
To seal
tire
punctures
and
prevent
flat tires
due to stow
leaks,
purchase
and
use tire sealant
from
Sears.
Tire
sealant
also
prevents
tire dry
rot and corrosion.
Washers
Retaining
Ring ,\
Axle
\
Square Key
(Rear Wheel Only)
|
TO
START
ENGINE
WITH
A WEAK
BATTERY
_WARNING:
Lead-acid
batteries
generate
explosive
gases.
Keep
sparks,
flame
and
smoking
materials
away
from
batteries,
Always
wear
eye
protection
when
around
batteries.
If your battery is too weak to start the engine,
it
should be recharged.
(See "BATTERY"
in the
MAINTENANCE
section
of this
manual),
If "jumper
cables"
are used
for
emergency
starting,
follow
this
procedure:
IMPORTANT:
"-four tractor
is equipped
with
a 12 volt system.
The other vehicle
must also
be a 12 volt system.
Do not use your
tractor
battery
to start
other
vehicles.
TO
A'I-FACH
JUMPER
CABLES
-
1.
Connect
one end of the RED cable to the
POSITIVE
(+) terminal
of each battery(A-
B), taking
care not to short against
tractor
chassis.
2.
Connect
one
end
of the
BLACK
cable
to the NEGATIVE
(-) terminal
(C) of fully
charged
battery.
3.
Connect
the
other
end
of
the
BLACK
cable
(D) to good
chassis
ground,
away
from
fuel tank
and
battery.
24
REVISION
E
LLANTAS
Las llantas en
masiado en la
presi6n de fas
para obtener
.
Reduzca la
REVISION
[:,
CONJUNTO
Para obtener t
la caja de la sl
en la forma ac
LA CAJA
DE 1
Servicio y Aju.'
REVISION
E
DA
DE TOD
Vea las figura.,
las correas de
segadora y de
Servicio y Aju,
las correas si_
REV1SION
E
Una vez que L
jar su tractor,
correctamente
FUNCtONA
B
servicio y ajus