D-Link DFL-1100 Product Manual - Page 57

L2TP/PPTP Clients

Get D-Link DFL-1100 - Security Appliance PDF manuals and user guides
UPC - 790069270239
View all D-Link DFL-1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

L2TP/PPTP Clients Settings for L2TP/PPTP Client Configuration Name - Specifies a friendly name for the PPTP/L2TP Client tunnel. Username - Specify the username for this PPTP/L2TP Client tunnel. Password/Confirm Password - The password to use for this PPTP/L2TP Client tunnel. Interface IP - Specifies if the L2TP/PPTP Client tunnel should use a Static IP or obtain a dynamic IP from the server. Remote Gateway - The IP address of the remote PPTP/L2TP Server. Dial on demand - If enabled the tunnel will only be initiated when needed. If disabled the tunnel will be persistent (always on). Authentication protocol - Specify which authentication protocol to use (if any). Refer to the Authentication Protocols section for more information about each type. MPPE encryption - If MPPE encryption is to be used, select the desired level of encryption key (MPPE is used with PPTP). A selection of None means that data will be sent over the PPP link unencrypted. Require IPSec encryption - If configuring for L2TP, you most likely will be using IPSec instead of MPPE for data encryption. To use IPSec enable the checkbox and select PSK or Certificate.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
L2TP/PPTP Clients
Settings for L2TP/PPTP
Client Configuration
Name
– Specifies a friendly
name for the PPTP/L2TP Client
tunnel.
Username
–
Specify
the
username for this PPTP/L2TP
Client tunnel.
Password/Confirm Password
–
The password to use for this
PPTP/L2TP Client tunnel.
Interface IP -
Specifies if the
L2TP/PPTP Client tunnel should
use a Static IP or obtain a
dynamic IP from the server.
Remote
Gateway
-
The
IP
address
of
the
remote
PPTP/L2TP Server.
Dial on demand
– If enabled the tunnel will only be initiated when needed. If disabled the
tunnel will be persistent (always on).
Authentication
protocol
–
Specify
which
authentication
protocol to use (if any). Refer to
the
Authentication
Protocols
section
for
more
information
about each type.
MPPE encryption
– If MPPE
encryption is to be used, select
the desired level of encryption
key (MPPE is used with PPTP). A
selection of
None
means that
data will be sent over the PPP
link unencrypted.
Require IPSec encryption
– If
configuring for L2TP, you most
likely will be using IPSec instead
of MPPE for data encryption. To
use IPSec enable the checkbox
and select PSK or Certificate.