D-Link DGS-3208F Product Manual - Page 42

Con Ports, Con Advanced Switch Features screen

Get D-Link DGS-3208F - Switch PDF manuals and user guides
UPC - 790069222092
View all D-Link DGS-3208F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Gigabit Ethernet Switch User's Guide Figure 6-12. Configure Advanced Switch Features screen The field you can set is: ♦ Head Of Line (HOL) Blocking Prevention If Enabled, this function is designed to prevent forwarding a packet to a "blocking" port, that is, a port where an excess of packets are queued up. Note that when a multicast packet or a packet with an unknown destination address needs to be forwarded to several ports, and if some of them are "blocking", the packet will not be discarded, rather it will be forwarded only to the ports that are not "blocking." Configure Ports The Port Configuration screen allows you to change the port state in the case when you would like to partition a port, or for observation, device repair, or security reasons. Great caution, however, must be observed when partitioning a port; you should make sure that the partitioned port is not being used as the port to control or monitor the condition of other devices. To change the configuration of a port: 1. Select System Configuration from the main menu and then choose Configure Ports. The following screen appears: 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Gigabit Ethernet Switch User’s Guide
35
Figure 6-12.
Configure Advanced Switch Features screen
The field you can set is:
♦
Head Of Line (HOL) Blocking Prevention
If
Enabled
, this function is designed to prevent forwarding
a packet to a “blocking” port, that is, a port where an excess of packets are queued up. Note that when a
multicast packet or a packet with an unknown destination address needs to be forwarded to several ports,
and if some of them are “blocking”, the packet will not be discarded, rather it will be forwarded only to the
ports that are not “blocking.”
Configure Ports
The
Port Configuration
screen allows you to change the port state in the case when you would like to
partition a port, or for observation, device repair, or security reasons. Great caution, however, must be
observed when partitioning a port; you should make sure that the partitioned port is not being used as the
port to control or monitor the condition of other devices.
To change the configuration of a port:
1.
Select
System
Configuration
from the main menu and then choose
Configure Ports
. The following
screen appears: