D-Link DGS-3208F Product Manual - Page 45

Con Spanning Tree Protocol, STP Parameters Setting screen

Get D-Link DGS-3208F - Switch PDF manuals and user guides
UPC - 790069222092
View all D-Link DGS-3208F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Gigabit Ethernet Switch User's Guide you will connect a monitoring/troubleshooting device such as a sniffer or an RMON probe. When you are finished, change the Status to Enabled and then press APPLY to let your changes take effect. Configure Spanning Tree Protocol The Spanning Tree Algorithm Parameters can be used for creating alternative paths in your network. The Protocol Parameters allow you to change the behind the scene parameters of the Spanning Tree Algorithm at the bridge level. The parameters for this section have been fully explained in Chapter 5's "Switch Management Concepts." See STA Operation Levels: On the Bridge level, and User-Changeable Parameters. It is recommended that you read these sections, as well as the introductory section in the same chapter entitled Spanning Tree Algorithm before changing any of the parameters. To change the Protocol Parameters: 1. Choose Configure Spanning Tree Protocol from the System Configuration menu. The following Configure Spanning Tree Protocol menu will be displayed: Figure 6-15. Configure Spanning Tree Protocol menu 2. Choose STP Parameter Settings to access the following screen: Figure 6-16. STP Parameters Setting screen 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Gigabit Ethernet Switch User’s Guide
38
you will connect a monitoring/troubleshooting device such as a sniffer or an RMON probe. When you are
finished, change the Status to
Enabled
and then press APPLY to let your changes take effect.
Configure Spanning Tree Protocol
The Spanning Tree Algorithm Parameters can be used for creating alternative paths in your network. The
Protocol Parameters allow you to change the behind the scene parameters of the Spanning Tree Algorithm at
the bridge level. The parameters for this section have been fully explained in Chapter 5’s “
Switch
Management Concepts.
” See
STA Operation Levels: On the Bridge level
, and
User-Changeable Parameters
. It is
recommended that you read these sections, as well as the introductory section in the same chapter entitled
Spanning Tree Algorithm
before changing any of the parameters.
To change the Protocol Parameters:
1.
Choose
Configure Spanning Tree Protocol
from the
System Configuration
menu. The following
Configure Spanning Tree Protocol
menu will be displayed:
Figure 6-15.
Configure Spanning Tree Protocol menu
2.
Choose
STP Parameter Settings
to access the following screen:
Figure 6-16.
STP Parameters Setting screen