Dell 2350DN User Guide - Page 30

Settings

Page 30 highlights

From this menu: You can: Receive information at a much higher transmission rate if the printer is set to Fastbytes (if computer supports Fastbytes), or receive information at a normal transmission rate if the printer is set to Standard. Honor Init Standard Fastbytes* Determine whether the printer honors hardware initialization requests from the computer. The computer requests initialization by activating the INIT signal on the parallel interface. Many personal computers activate the INIT signal each time the computer is turned on and off. Parallel Mode 2 On Off* Determine whether the parallel port data is sampled on the leading (on) or trailing (off) edge of the strobe. Off On* NOTE: This menu appears only if supported by the parallel port. MAC Binary Configure the printer to process Macintosh binary PostScript emulation print PS jobs. Off On Auto* Parallel With Configure the parallel port ENA address, Netmask, and Gateway settings. ENA 4 field IP address (0.0.0.0*) ENA Address NOTE: These settings are shown only when ENA is attached through the ENA parallel port. Netmask ENA Gateway * Factory default setting Settings Mode Settings Mode Main Menu General Settings Setup Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181

From this
menu:
You can:
to Fastbytes (if computer supports Fastbytes), or receive information at a
normal transmission rate if the printer is set to Standard.
Standard
Fastbytes*
Honor Init
Determine whether the printer honors hardware initialization requests from
the computer. The computer requests initialization by activating the INIT
signal on the parallel interface.
Many personal computers activate the INIT signal each time the computer is
turned on and off.
On
Off*
Parallel
Mode 2
Determine whether the parallel port data is sampled on the leading (on) or
trailing (off) edge of the strobe.
Off
On*
NOTE:
This menu appears only if supported by the parallel port.
MAC Binary
PS
Configure the printer to process Macintosh binary PostScript emulation print
jobs.
Off
On
Auto*
Parallel With
ENA
ENA
Address
ENA
Netmask
ENA
Gateway
Configure the parallel port ENA address, Netmask, and Gateway settings.
4 field IP address (0.0.0.0*)
NOTE:
These settings are shown only when ENA is attached through the
parallel port.
* Factory default setting
Settings
Mode
Mode Main Menu
Settings
General Settings
Setup Menu