Dell Inspiron 16 Plus 7640 Owners Manual - Page 70

Installing the power-adapter port

Get Dell Inspiron 16 Plus 7640 PDF manuals and user guides View all Dell Inspiron 16 Plus 7640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

6. Lift the power-adapter port off the palm-rest and keyboard assembly. Installing the power-adapter port CAUTION: The information in this section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the power-adapter port and provides a visual representation of the installation procedure. Figure 45. Installing the power-adapter port Steps 1. Place the power-adapter port into the slot on the palm-rest and keyboard assembly. 2. Route the power-adapter port cable through the routing guide on the palm-rest and keyboard assembly. 3. Connect the power-adapter port to its connector on the palm-rest and keyboard assembly. 4. Adhere the tape that secures the power-adapter port cable to its connector on the palm-rest and keyboard assembly. 5. Close the display hinge and align the screw holes on the display hinge with the screw holes on the palm-rest and keyboard assembly. 6. Replace the three screws (M2.5x5) that secure the right display-assembly hinge to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. 70 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
6.
Lift the power-adapter port off the palm-rest and keyboard assembly.
Installing the power-adapter port
CAUTION:
The information in this section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the power-adapter port and provides a visual representation of the installation
procedure.
Figure 45. Installing the power-adapter port
Steps
1.
Place the power-adapter port into the slot on the palm-rest and keyboard assembly.
2.
Route the power-adapter port cable through the routing guide on the palm-rest and keyboard assembly.
3.
Connect the power-adapter port to its connector on the palm-rest and keyboard assembly.
4.
Adhere the tape that secures the power-adapter port cable to its connector on the palm-rest and keyboard assembly.
5.
Close the display hinge and align the screw holes on the display hinge with the screw holes on the palm-rest and keyboard
assembly.
6.
Replace the three screws (M2.5x5) that secure the right display-assembly hinge to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
70
Removing and installing Field Replaceable Units (FRUs)