Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.20.0 - Page 122

Table 22. Command description, Table 23. Command description, Table 24. Command description, Table

Get Dell PowerEdge MX7000 PDF manuals and user guides View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

f. (Optional) View the status of the current software install in EXEC mode. Table 22. Command description Command Description OS10# show image status View the status of the current software install. g. Change the next boot partition to the standby partition in EXEC mode. Use the active parameter to set the next boot partition from standby to active. Table 23. Command description Command Description OS10# boot system standby Change the next boot partition to standby. h. (Optional) Check whether the next boot partition has changed to standby in EXEC mode. Table 24. Command description Command OS10# show boot detail i. Reload the new software image in EXEC mode. Description Check whether the next boot partition has changed. Table 25. Command description Command Description OS10# reload Reload the new software. j. After the installation is complete, enter the show version command to check if the latest version of the software that you have installed is running in the system. The example below shows that the 10.5.0.5 software is installed and running on the system. OS10# show version MX9116N-A2# show version Dell EMC Networking OS10 Enterprise Copyright (c) 1999-2020 by Dell Inc. All Rights Reserved. OS Version: 10.5.0.5 Build Version: 10.5.0.5.661 Build Time: 2020-02-15T00:45:32+0000 System Type: MX9116N-ON Architecture: x86_64 Up Time: 1 day 20:37:53 MX9116N-A2# 5. Run the command, show smartfabric cluster member, in the Master networking switch. Confirm that the STATUS of the upgraded switch is ONLINE in the command output, after it has reloaded. IOM# show smartfabric cluster member Service-tag IP Address Status Role Type Tag Chassis-Slot MXWV122 xxxxxxxxxxx ONLINE MASTER MX9116n SKYMX02 MXLE103 xxxxxxxxxxx ONLINE BACKUP MX9116n SKYMX10 MXLE093 xxxxxxxxxxx ONLINE BACKUP MX9116n SKYMX09 MXWV011 xxxxxxxxxxx ONLINE BACKUP MX9116n SKYMX01 Chassis-ServiceA2 B2 B1 A1 6. After step 5 is completed, proceed with upgrading the next Networking I/O Module. After all the IOMs are updated, the update process of all components in the MX7000 update procedure is complete. Verify that all expected data path links are up and passing traffic. If you experience network link or performance issues, power cycle (cold boot) the MX7000 chassis. For details, see Controlling chassis power. 122 Upgrading networking switch using CLI

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
f.
(Optional)
View the status of the current software install in EXEC mode.
Table 22. Command description
Command
Description
OS10# show image status
View the status of the current software install.
g.
Change the next boot partition to the standby partition in EXEC mode. Use the active parameter to set the next boot
partition from standby to active.
Table 23. Command description
Command
Description
OS10# boot system standby
Change the next boot partition to standby.
h.
(Optional)
Check whether the next boot partition has changed to standby in EXEC mode.
Table 24. Command description
Command
Description
OS10# show boot detail
Check whether the next boot partition has changed.
i.
Reload the new software image in EXEC mode.
Table 25. Command description
Command
Description
OS10# reload
Reload the new software.
j.
After the installation is complete, enter the show version command to check if the latest version of the software that you
have installed is running in the system.
The example below shows that the 10.5.0.5 software is installed and running on the system.
OS10# show version
MX9116N-A2# show version
Dell EMC Networking OS10 Enterprise
Copyright (c) 1999-2020 by Dell Inc. All Rights Reserved.
OS Version: 10.5.0.5
Build Version: 10.5.0.5.661
Build Time: 2020-02-15T00:45:32+0000
System Type: MX9116N-ON
Architecture: x86_64
Up Time: 1 day 20:37:53
MX9116N-A2#
5.
Run the command,
show smartfabric cluster member
, in the Master networking switch. Confirm that the
STATUS
of the upgraded switch is
ONLINE
in the command output, after it has reloaded.
IOM# show smartfabric cluster member
Service-tag
IP Address
Status
Role
Type
Chassis-Service-
Tag
Chassis-Slot
MXWV122
xxxxxxxxxxx
ONLINE
MASTER
MX9116n
SKYMX02
A2
MXLE103
xxxxxxxxxxx
ONLINE
BACKUP
MX9116n
SKYMX10
B2
MXLE093
xxxxxxxxxxx
ONLINE
BACKUP
MX9116n
SKYMX09
B1
MXWV011
xxxxxxxxxxx
ONLINE
BACKUP
MX9116n
SKYMX01
A1
6.
After step 5 is completed, proceed with upgrading the next Networking I/O Module.
After all the IOMs are updated, the update process of all components in the MX7000 update procedure is complete. Verify
that all expected data path links are up and passing traffic. If you experience network link or performance issues, power
cycle (cold boot) the MX7000 chassis. For details, see
Controlling chassis power
.
122
Upgrading networking switch using CLI