Dell PowerEdge MX7000 EMC OpenManage Enterprise-Modular Edition Version 1.20.0 - Page 15
Updating OME-Modular to 1.20.00, Recovering failed Management Module firmware update process
![]() |
View all Dell PowerEdge MX7000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Emulex Picard-16/Picard-32 adapters, as applicable. Go to dell.com to download the latest device drivers associated with the firmware update. Updating OME-Modular to 1.20.00 If the current version is 1.00.01 or 1.00.10, update OME-Modular to 1.10.00 or 1.10.10 before updating to 1.10.20. You can update to OME-Modular 1.20.00 only if the existing version of OME-Modular on your system is 1.10.20. For more information, see Updating OME-Modular to 1.10.10 and Updating OME-Modular to 1.10.20, and Updating Fabric Switching Engine and Ethernet Switch. NOTE: Updating to 1.10.x may result in the alert log alert HWC7522, and you may have to perform a system reseat on the MX7116n or pass-through module (PTM) IOMs. Recovering failed Management Module firmware update process If the firmware update of a management module (MM) fails, perform the following steps: 1. Perform a failover on the MM. If the failover fails, go to step 2. 2. Reset the active MM manually. 3. After the failover or reset is complete, check the firmware version to verify if the active MM is running the same or a later version of OME-Modular, as the standby MM. If not, perform a reset on the MM to force failover. 4. Retry the firmware update. Updating IOMs using OME-Modular 1. If OME-Modular is managing a chassis group, then log in to OME-Modular interface of the Lead chassis. 2. Click Devices > I/O Modules. A list of the available IOMs in the chassis or chassis group is displayed. 3. In the list header, select the checkbox to select all IOMs on the current page. If there are multiple pages, then go to each page and select the checkbox. 4. After selecting all the I/O Modules, click Update Firmware. 5. In the pop-up wizard, select the Individual Package and click Browse to select the I/O Module DUP. 6. Once the DUP is uploaded, click Next and select the Compliance checkbox. 7. Click Finish to start the update on all I/O Modules. Upgrading networking switch using DUP NOTE: This procedure is recommended for upgrading OS10 on the MX9116n and MX5108n switches. NOTE: You can directly upgrade the MX9116n and MX5108n switches to the corresponding OME-Modular 1.20.00 baseline version, 10.5.0.7. NOTE: Upgrade the MX9116n and MX5108n switches only after updating the other MX7000 components to their corresponding OME-M 1.20.00 baseline versions. NOTE: Upgrading VLT peers from 10.4.0E(R3S) or 10.4.0E(R4S) to 10.5.0.X, impacts traffic. To upgrade OS10 using DUP, follow these steps: 1. Download the latest DUP file for the switch from https://www.dell.com/support. 2. On the OME-Modular web interface, go to Devices > I/O Modules. 3. Select the IOM module on which you must carry out the OS10 upgrade. 4. Click Update Firmware. 5. Select the Individual package option, then click Browse and go to the location where the DUP was downloaded earlier. Wait for the compliance report, once done, the supported components are displayed. 6. Select the required components and click Update, to start the update. Updating the management module firmware 15
![](/manual_guide/products/dell-poweredge-mx7000-emc-openmanage-enterprisemodular-edition-version-12000-chassis-users-guide-a1de94a/15.png)