Dell PowerVault NX300 Hardware Owner's Manual - Page 110

Replacing a Cooling Fan, Optical Drive, Removing an Optical Drive

Get Dell PowerVault NX300 PDF manuals and user guides View all Dell PowerVault NX300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Replacing a Cooling Fan 1 Ensure that the fan is oriented correctly. Orient the fan module so that the side with the power cable faces towards the back of the system. 2 Slide the fan module into the fan assembly until the fan is fully seated. See Figure 3-16. 3 Connect the fan's power cable to the power connector on the system board. 4 Replace the system board shroud. See "Installing the System Board Shroud" on page 103. 5 Close the system. See "Closing the System" on page 83. 6 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. Optical Drive An optional slimline DVD or DVD-RW optical drive slides into the front panel and connects to the SATA controller on the system board. NOTE: DVD devices are data only. Removing an Optical Drive CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 If installed, remove the optional front bezel. See "Removing and Replacing the Optional Front Bezel" on page 81. 2 Turn off the system, including any attached peripherals, and disconnect the system from its electrical outlet. 3 Open the system. See "Opening the System" on page 82. 4 Disconnect the power and data cables from the back of the drive. 110 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
110
Installing System Components
Replacing a Cooling Fan
1
Ensure that the fan is oriented correctly.
Orient the fan module so that the side with the power cable faces towards
the back of the system.
2
Slide the fan module into the fan assembly until the fan is fully seated. See
Figure 3-16.
3
Connect the fan’s power cable to the power connector on the system
board.
4
Replace the system board shroud. See "Installing the System Board
Shroud" on page 103.
5
Close the system. See "Closing the System" on page 83.
6
Reconnect the system to its electrical outlet and turn the system on,
including any attached peripherals.
Optical Drive
An optional slimline
DVD or DVD-RW
optical drive slides into the front panel
and connects to the SATA controller on the system board.
NOTE:
DVD devices are data only.
Removing an Optical Drive
CAUTION:
Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
If installed, remove the optional front bezel. See "Removing and Replacing
the Optional Front Bezel" on page 81.
2
Turn off the system, including any attached peripherals, and disconnect
the system from its electrical outlet.
3
Open the system. See "Opening the System" on page 82.
4
Disconnect the power and data cables from the back of the drive.