Dell XPS 13 9340 Owners Manual - Page 52

Removing the display assembly

Get Dell XPS 13 9340 PDF manuals and user guides View all Dell XPS 13 9340 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Figure 34. Removing the display assembly Steps 1. Loosen the three captive screws (M1.6x2) that secure the display-assembly cable bracket to the system board. 2. Lift the display-assembly cable bracket off the system board. 3. Disconnect the camera cable and the display cable from the system board. 4. Remove the three screws (M1.6x2.5) that secure the camera and display-assembly cable holder to the system board. 5. Open the display to a 90-degree angle and place the computer at the edge of a flat table. 6. Remove the three screws (M2.5x5) that secure the left hinge to the system board and the palm-rest and keyboard assembly. 7. Remove the three screws (M2.5x5) that secure the right hinge to the system board and the palm-rest and keyboard assembly. 52 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Figure 34. Removing the display assembly
Steps
1.
Loosen the three captive screws (M1.6x2) that secure the display-assembly cable bracket to the system board.
2.
Lift the display-assembly cable bracket off the system board.
3.
Disconnect the camera cable and the display cable from the system board.
4.
Remove the three screws (M1.6x2.5) that secure the camera and display-assembly cable holder to the system board.
5.
Open the display to a 90-degree angle and place the computer at the edge of a flat table.
6.
Remove the three screws (M2.5x5) that secure the left hinge to the system board and the palm-rest and keyboard
assembly.
7.
Remove the three screws (M2.5x5) that secure the right hinge to the system board and the palm-rest and keyboard
assembly.
52
Removing and installing Field Replaceable Units (FRUs)