Dell XPS 16 9640 Owners Manual - Page 43

Installing the battery cable, Prerequisites, About this task, Steps

Get Dell XPS 16 9640 PDF manuals and user guides View all Dell XPS 16 9640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. 3. Remove the battery. About this task NOTE: If the battery is disconnected from the system board for service, there is a delay during boot as the computer undergoes an RTC battery reset. The following image(s) indicate the location of the battery cable and provides a visual representation of the removal procedure. Figure 20. Removing the battery cable Steps 1. Turn the battery over. 2. Peel the battery cable from the battery until you reach the end where it connects the cable to the battery. 3. Grasp the battery cable near the connector and lift to disconnect it from the battery. Installing the battery cable CAUTION: The information in this installation section is intended for authorized service technicians only. Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the battery cable and provides a visual representation of the installation procedure. Removing and installing Field Replaceable Units (FRUs) 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
3.
Remove the
battery
.
About this task
NOTE:
If the battery is disconnected from the system board for service, there is a delay during boot as the computer
undergoes an RTC battery reset.
The following image(s) indicate the location of the battery cable and provides a visual representation of the removal procedure.
Figure 20. Removing the battery cable
Steps
1.
Turn the battery over.
2.
Peel the battery cable from the battery until you reach the end where it connects the cable to the battery.
3.
Grasp the battery cable near the connector and lift to disconnect it from the battery.
Installing the battery cable
CAUTION:
The information in this installation section is intended for authorized service technicians only.
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the battery cable and provides a visual representation of the installation
procedure.
Removing and installing Field Replaceable Units (FRUs)
43