Dell XPS 16 9640 Owners Manual - Page 51

Heat sink, Removing the heat sink—Integrated GPUs

Get Dell XPS 16 9640 PDF manuals and user guides View all Dell XPS 16 9640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Figure 29. Installing the M.2 2280 solid-state drive Steps 1. Align the notch on the solid-state drive with the tab on the solid-state drive slot (SSD1) on the system board. 2. Slide the solid-state drive into the solid-state drive slot (SSD1) on the system board. 3. Align the screw holes on the thermal shield with the screw holes on the system board. 4. Replace the two screws (M2x3) that secure the thermal shield to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Heat sink Removing the heat sink-Integrated GPUs CAUTION: The information in this removal section is intended for authorized service technicians only. Prerequisites 1. Follow the procedure in Before working inside your computer. 2. Remove the base cover. About this task CAUTION: The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you touch it. NOTE: For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin can reduce the heat transfer capability of the thermal grease. Removing and installing Field Replaceable Units (FRUs) 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Figure 29. Installing the M.2 2280 solid-state drive
Steps
1.
Align the notch on the solid-state drive with the tab on the solid-state drive slot (SSD1) on the system board.
2.
Slide the solid-state drive into the solid-state drive slot (SSD1) on the system board.
3.
Align the screw holes on the thermal shield with the screw holes on the system board.
4.
Replace the two screws (M2x3) that secure the thermal shield to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Heat sink
Removing the heat sink—Integrated GPUs
CAUTION:
The information in this removal section is intended for authorized service technicians only.
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
2.
Remove the
base cover
.
About this task
CAUTION:
The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool
before you touch it.
NOTE:
For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin
can reduce the heat transfer capability of the thermal grease.
Removing and installing Field Replaceable Units (FRUs)
51