Dell XPS 16 9640 Owners Manual - Page 62

Type-C bracket, Removing the Type-C brackets

Get Dell XPS 16 9640 PDF manuals and user guides View all Dell XPS 16 9640 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Figure 40. Installing the display assembly Steps 1. Place the palm-rest assembly at the edge of a flat table. CAUTION: To avoid damaging the display, do not slide palm rest and keyboard assembly on the display assembly. 2. Align the screw holes of the palm-rest assembly with the screw holes on the hinges of the display assembly. 3. Replace the two screws (M2.5x6) that secure the right-display hinge to the palm rest and keyboard assembly and open the right hinge. 4. Replace the two screws (M2.5x6) that secure the left-display hinge to the palm rest and keyboard assembly and open the left hinge. 5. Align the screw holes on the display-cable connector bracket with the screw holes on the system board. 6. Replace the two screws (M2x3) that secure the display-cable connector bracket to the system board. 7. Replace the two screws (M1.4x1.3) that secure the display-cable cover to the display-cable connector bracket. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Type-C bracket Removing the Type-C brackets CAUTION: The information in this removal section is intended for authorized service technicians only. 62 Removing and installing Field Replaceable Units (FRUs)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Figure 40. Installing the display assembly
Steps
1.
Place the palm-rest assembly at the edge of a flat table.
CAUTION:
To avoid damaging the display, do not slide palm rest and keyboard assembly on the display
assembly.
2.
Align the screw holes of the palm-rest assembly with the screw holes on the hinges of the display assembly.
3.
Replace the two screws (M2.5x6) that secure the right-display hinge to the palm rest and keyboard assembly and open the
right hinge.
4.
Replace the two screws (M2.5x6) that secure the left-display hinge to the palm rest and keyboard assembly and open the
left hinge.
5.
Align the screw holes on the display-cable connector bracket with the screw holes on the system board.
6.
Replace the two screws (M2x3) that secure the display-cable connector bracket to the system board.
7.
Replace the two screws (M1.4x1.3) that secure the display-cable cover to the display-cable connector bracket.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Type-C bracket
Removing the Type-C brackets
CAUTION:
The information in this removal section is intended for authorized service technicians only.
62
Removing and installing Field Replaceable Units (FRUs)