Denon 2106 Operating Instructions - Page 11

Setup Mic, On/standby, On/source, Speaker A, Power, Mode 1 - room eq

Get Denon 2106 - AVR AV Receiver PDF manuals and user guides
UPC - 081757506571
View all Denon 2106 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Easy Setup and Operation POWER SPEAKER A MODE 1 ON/SOURCE ENGLISH Turning on the power Easy Setup and Operation 1 Turn on your subwoofer. ON/STANDBY SETUP MIC SETUP ENTER CURSOR SPEAKER Auto Setup / Room EQ The Auto Setup and Room EQ function of this unit performs an analysis of the speaker system and measures the acoustic characteristics of your room to permit an appropriate automatic setting. 2 Measurement and setting details q: This sets the speaker connection, polarity, and bass reproduction ability. w: This sets the delay time from each speaker corresponding to the listening position. e: This sets the volume that is output from each speaker. r: This sets the frequency response of each speaker. Connecting a microphone 1 Connect the microphone for Auto Setup to the SETUP MIC jack on the front panel of the unit. For accurate measurements • Keep quiet during the auto setup procedure. It is recommended that you turn off the power of any air-conditioner, projector or other equipment that may produce noise. • Do not stand between the microphone and speakers while Auto Setup is performed. • Do not place any obstacles between the microphone and speakers. Also, be sure to point the speakers towards the listening position. NOTE: • A loud test tone is output during the measurement. Please consider this should you be planning night time measurements, and consider not allowing small children into the listening room at this time. 2 Place the microphone for Auto Setup at the actual listening position which will be at the same height as your ears. Microphone Place the microphone on a tripod or level surface. 2 Turn on your monitor (TV). 3 Press the POWER switch. ¢ ON: The power turns on and the indicator lights. Set the POWER switch to this position to turn the power on and off from the included remote control unit. £ OFF: The power turns off and the indicator is off. In this position, the power cannot be turned on and off from the remote control unit. 4 Press the ON/STANDBY switch on the main unit or ON/SOURCE button on the remote control unit. • Turn on the power. 5 Press the SPEAKER A button to turn the speakers on. 6 Set the MODE 1 switch to "AUDIO" (only when operating with the remote control unit). 8 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
ENGLISH
8
Easy Setup and Operation
Easy Setup and Operation
ENGLISH
The Auto Setup and Room EQ function of this unit performs an
analysis of the speaker system and measures the acoustic
characteristics of your room to permit an appropriate automatic
setting.
Auto Setup / Room EQ
2
Measurement and setting details
q
:This sets the speaker connection, polarity, and bass
reproduction ability.
w
:This sets the delay time from each speaker corresponding to
the listening position.
e
:This sets the volume that is output from each speaker.
r
:This sets the frequency response of each speaker.
Connecting a microphone
1
Connect the microphone for Auto Setup to the
SETUP MIC
jack on the front panel of the unit.
2
Place the microphone for Auto Setup at the
actual listening position which will be at the
same height as your ears.
Microphone
NOTE:
• A loud test tone is output during the measurement. Please
consider this should you be planning night time
measurements, and consider not allowing small children
into the listening room at this time.
Place the microphone on a tripod or level surface.
For accurate measurements
• Keep quiet during the auto setup procedure. It is recommended
that you turn off the power of any air-conditioner, projector or
other equipment that may produce noise.
• Do not stand between the microphone and speakers while
Auto Setup is performed.
• Do not place any obstacles between the microphone and
speakers. Also, be sure to point the speakers towards the
listening position.
4
Press the
ON/STANDBY
switch on the main unit
or
ON/SOURCE
button on the remote control
unit.
• Turn on the power.
5
Press the
SPEAKER A
button to turn the speakers
on.
3
Press the
POWER
switch.
£
OFF:
The power turns off and the indicator is off.
In this position, the power cannot be turned on and off from
the remote control unit.
¢
ON:
The power turns on and the indicator lights.
Set the
POWER
switch to this position to turn the power on
and off from the included remote control unit.
1
Turn on your subwoofer.
Turn on your monitor (TV).
Turning on the power
6
Set the
MODE 1
switch to “AUDIO” (only when
operating with the remote control unit).
SETUP
MODE 1
CURSOR
SPEAKER
ON/SOURCE
ENTER
ON/STANDBY
SETUP MIC
POWER
SPEAKER A
2