Epson ActionNote 880C User Manual - Fax/Data Modem - Page 15

tion to the DTE., This command causes the modem to send product code and hardware setup informa

Get Epson ActionNote 880C PDF manuals and user guides View all Epson ActionNote 880C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

In Identification/Checksum Option This command causes the modem to send product code and hardware setup information to the DTE. I0 Report product code. (default) I1 Firmware version #. I2 Verify ROM checksum. I3 Device set name. I4 Modem configuration. Bit 0 0= Hayes Escape Sequence. 1 =TIES Escape Sequence, Bit 1 0= Data/fax/voice without V.42/MNP firmware. 1 =Data/fax/voice with V.42/MN P firmware. Bit 2 0= Serial host interface, 1 =Parallel host interface. Bit 3 0=No external Static RAM present. 1 =External Static RAM present, Bit 4 0=8K x 8 static RAM present. (valid only if bit 3 = 1 ) 1 =32K x 8 static RAM present. (valid only if bit 3 = 1) Bits 5-7 Reserved Kn Buffer Control This command selects whether the modem SRAM is used for voice and fax mode, K0 SRAM buffer disabled. (default when no SRAM is available) K1 SRAM buffer enabled. (default when the SRAM is available on modem board) (default) 2 - COMMAND REFERENCE 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
In
Identification/Checksum Option
This command causes the modem to send product code and hardware setup informa-
tion to the DTE.
I0
Report product code. (default)
I1
Firmware version #.
I2
Verify ROM checksum.
I3
Device set name.
I4
Modem configuration.
Bit 0
0= Hayes Escape Sequence.
1 =TIES Escape Sequence,
Bit 1
0= Data/fax/voice without V.42/MNP firmware.
1 =Data/fax/voice with V.42/MN P firmware.
Bit 2
0= Serial host interface,
1 =Parallel host interface.
Bit 3
0=No external Static RAM present.
1 =External Static RAM present,
Bit 4
0=8K x 8 static RAM present. (valid only if bit 3 = 1 )
1 =32K x 8 static RAM present. (valid only if bit 3 = 1)
Bits 5-7 Reserved
Kn
Buffer Control
This command selects whether the modem SRAM is used for voice and fax mode,
K0
SRAM buffer disabled. (default when no SRAM is available)
K1
SRAM buffer enabled. (default when the SRAM is available
on modem board) (default)
2 - COMMAND REFERENCE
7