Epson ActionNote 880C User Manual - Fax/Data Modem - Page 75

Manual Answer an lncoming Call, Command line: AT S0=2 &W &Y <CR&gt

Get Epson ActionNote 880C PDF manuals and user guides View all Epson ActionNote 880C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

6.3 Manual Answer an lncoming Call Command line: ATA The factory setting of the S-register SO is S0=0. This condition disables the auto answer capability so that you must issue an ATA command to answer a call. At power up, your modem always monitors if there are incoming rings. If incoming rings are detected, your modem will display result codes on the screen as: RING RING Seeing that, you may issue the ATA command to answer the call. This command must be entered within the quiet interval between any two rings. 6.4 Auto Answer an Incoming Call Command line: AT S0=2 &W &Y Auto answer can be enabled by changing the setting of the S-register SO to a value between 1 and 255. In the above command line, S0=2 instructs the modem to answer an incoming call automatically after the 2nd ring. The &W command writes this configuration to profile 0 in NVRAM. &Y command instruct the modem to load profile 0 as the active configuration on power-up. The last two commands make S0=2 the default value at power-up or reset. 68 APPLICATION EXAMPLES - 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
6.3 Manual Answer an lncoming Call
Command line: ATA <CR>
The factory setting of the S-register S
O
is S0=0. This condition disables the auto
answer capability so that you must issue an ATA command to answer a call. At
power up, your modem always monitors if there are incoming rings. If incoming
rings are detected, your modem will display result codes on the screen as:
RING
RING
Seeing that, you may issue the ATA command to answer the call. This command
must be entered within the quiet interval between any two rings.
6.4 Auto Answer an Incoming Call
Command line: AT S0=2 &W &Y <CR>
Auto answer can be enabled by changing the setting of the S-register SO to a value
between 1 and 255. In the above command line, S0=2 instructs the modem to an-
swer an incoming call automatically after the 2nd ring. The &W command writes this
configuration to profile 0 in NVRAM. &Y command instruct the modem to load
profile 0 as the active configuration on power-up. The last two commands make
S0=2 the default value at power-up or reset.
68
APPLICATION EXAMPLES - 6