Epson C850071 User Guide - Page 51

Port Setup Token Ring, Protocol Setup TCP/IP

Get Epson C850071 - RIP Station 5000 PDF manuals and user guides
UPC - 010343818118
View all Epson C850071 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Page 51 Port Setup (Token Ring) A Token Ring option is not available for the RIP Station. Therefore, these Setup options cannot be selected. TO CONFIGURE PROTOCOL SETUP: • Click the Protocol Setup tab in the Network Setup window. The RIP Station can accept jobs via TCP/IP (over Ethernet only), AppleTalk, and IPX/SPX simultaneously. To configure the RIP Station, choose each protocol and enter the settings for that protocol. Protocol Setup (TCP/IP) Enable on Ethernet-Click to enable if you have a TCP/IP network connected to the RIP Station over Ethernet cabling. You must enable TCP/IP for Ethernet to use Fiery WebTools over Ethernet. If you are using TCP/IP for printing from Windows NT 4.0 workstations, enabling TCP/IP here also enables you to use Fiery utilities from Windows NT 4.0 workstations using TCP/IP protocols. IP Address (Ethernet)-Enter the RIP Station IP address for Ethernet. You must change the default 127.0.0.1 to a valid address for your network. For information about setting up printing with TCP/IP, see Chapter 3 in the Administrator Guide. Subnet Mask (Ethernet)-If you need to set the subnet mask, enter one of the following values: • 255.0.0.0 if the IP address starts with a number less than 128 • 255.255.0.0 if the IP address starts with a number from 128 through 191 • 255.255.255.0 if the IP address starts with a number greater than 191 NOTE: Be sure to confirm the subnet mask setting with your network administrator before proceeding. In some cases, the required setting may be different from those listed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Page 51
Port Setup (Token Ring)
A Token Ring option is not available for the RIP Station. Therefore, these Setup options
cannot be selected.
T
O
CONFIGURE
P
ROTOCOL
S
ETUP
:
•
Click the Protocol Setup tab in the Network Setup window.
The RIP Station can accept jobs via TCP/IP (over Ethernet only), AppleTalk, and IPX/SPX
simultaneously. To configure the RIP Station, choose each protocol and enter the settings
for that protocol.
Protocol Setup (TCP/IP)
Enable on Ethernet
—Click to enable
if you have a TCP/IP network connected to the
RIP Station over Ethernet cabling.
You must enable TCP/IP for Ethernet to use Fiery WebTools over Ethernet.
If you are
using TCP/IP for printing from Windows NT 4.0 workstations, enabling TCP/IP here also
enables you to use Fiery utilities from Windows NT 4.0 workstations using TCP/IP proto-
cols.
IP Address (Ethernet)
—Enter the RIP Station IP address for Ethernet. You must change
the default
127.0.0.1
to a valid address for your network. For information about setting up
printing with TCP/IP, see Chapter 3 in the
Administrator Guide
.
Subnet Mask (Ethernet)
—If you need to set the subnet mask, enter one of the following
values:
•
255.0.0.0
if the IP address starts with a number less than 128
•
255.255.0.0
if the IP address starts with a number from 128 through 191
•
255.255.255.0
if the IP address starts with a number greater than 191
N
OTE
:
Be sure to confirm the subnet mask setting with your network administrator before
proceeding. In some cases, the required setting may be different from those listed.