Epson MegaPlex MG-850HD User Manual - Page 17

Installing Batteries in the Remote Control, Turning the Projector On and Off, Turning On the Projector

Get Epson MegaPlex MG-850HD PDF manuals and user guides View all Epson MegaPlex MG-850HD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installing Batteries in the Remote Control The remote control uses two AAA batteries. Warning: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover. 2. Insert two new AAA batteries as shown. 3. Insert the tab on the cover and press it down until it clicks into place. Aim the remote control at the screen, or at the front or back of the projector. Make sure you are within 20 feet (6 m) of the projector. If you suspect the batteries are weak, press the illumination button. If the playback and volume buttons do not glow, replace the batteries. Turning the Projector On and Off Turning On the Projector 1. Slide open the lens cover. 2. Turn on any connected equipment you plan to use. 3. Press the Ppower button on the remote control or on the projector. Note: To prevent children from turning on the projector, you can use the Child Lock feature. See page 47 for details. If you'll be using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure. See page 50 for details. The projector takes about 30 seconds to warm up and display an image. If you don't see a picture, you may need to change the image source as described on page 37. Installing Batteries in the Remote Control 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
Installing Batteries in the Remote Control
17
Installing Batteries in the Remote Control
The remote control uses two AAA batteries.
Warning:
Keep batteries away from children. If a battery is swallowed, contact your doctor
immediately.
1.
Release the tab and lift open the cover.
2.
Insert two new AAA batteries as shown.
3.
Insert the tab on the cover and press it down until it clicks
into place.
Aim the remote control at the screen, or at the front or back of
the projector. Make sure you are within 20 feet (6 m) of the
projector.
If you suspect the batteries are weak, press the
illumination button. If the playback and
volume buttons do not glow, replace the batteries.
Turning the Projector On and Off
Turning On the Projector
1.
Slide open the lens cover.
2.
Turn on any connected equipment you plan to use.
3.
Press the
P
power button on the remote control or on
the projector.
Note:
To prevent children from turning on the projector, you
can use the Child Lock feature. See page 47 for details.
If you’ll be using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude
Mode so the fan can properly cool the projector at the high altitude air pressure. See page 50 for
details.
The projector takes about 30 seconds to warm up and display an image. If you don’t see a picture,
you may need to change the image source as described on page 37.