Fujitsu MAB3091SC Product Manual - Page 57

Mounting, 4.1.3 Notes on mounting, As shown

Get Fujitsu MAB3091SC - Enterprise 9.1 GB Hard Drive PDF manuals and user guides View all Fujitsu MAB3091SC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

4.1.2 Mounting The permissible orientations of the IDD are shown in Figure 4.5, and the tolerance of the angle is ±5° from the horizontal plane. (a) Horizontal -1 (b) Horizontal -2 Direction of gravity (c) Vertical -1 (d) Vertical -2 (e) Upright mounting -1 Figure 4.5 IDD orientation (f) Upright mounting -2 4.1.3 Notes on mounting (1) Mounting frame structure To guarantee integrity of the IDD disk enclosure (DE) insulation once mounted on the frame inside the system, special attention must be given to the note below. Note: Generally, SG and FG are connected at one point in the system enclosure. Therefore, use following procedure to maintain the insulation when mounting the IDD. a) Use the frame with an embossed structure or the like to avoid contact between the DE base and FG. Mount the IDD with making a gap of 2.5 mm or more between the IDD and the frame of the system. b) As shown in Figure 4.6, the inward projection of the screw from the IDD frame wall at the corner must be 4 mm or less. 4 - 6 C141-E035-02EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
C141-E035-02EN
4 - 6
4.1.2
Mounting
The permissible orientations of the IDD are shown in Figure 4.5, and the tolerance of the angle
is
±
5° from the horizontal plane.
Figure 4.5
IDD orientation
4.1.3
Notes on mounting
(1)
Mounting frame structure
To guarantee integrity of the IDD disk enclosure (DE) insulation once mounted on the frame
inside the system, special attention must be given to the note below.
Note:
Generally, SG and FG are connected at one point in the system enclosure.
Therefore, use
following procedure to maintain the insulation when mounting the IDD.
a)
Use the frame with an embossed structure or the like to avoid contact between the DE
base and FG.
Mount the IDD with making a gap of 2.5 mm or more between the IDD
and the frame of the system.
b)
As shown in Figure 4.6, the inward projection of the screw from the IDD frame wall
at the corner must be 4 mm or less.
Direction of
gravity
(a)
Horizontal
–1
(b) Horizontal
–2
(c)
Vertical –1
(d)
Vertical –2
(e)
Upright mounting –1
(f)
Upright mounting –2