Home » Fujitsu Manuals » Hard Drives » Fujitsu MAB3091SC » Manual Viewer

Fujitsu MAB3091SC Product Manual - Page 86

SCSI ID setting, MAx3xxxSP CN7

Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

5.3.1 SCSI ID setting (1) SCA type 16-bit SCSI model (MAx3xxxSC) There is no SCSI ID setting terminal for SCA type model. Set the SCSI ID using ID0, ID1, ID2, and ID3 signals on the SCSI interface connector (CN1). (2) Single-ended 16-bit SCSI model (MAx3xxxSP) Table 5.1 shows the SCSI ID setting. Refer to Figures 5.2 and 5.3 for connector positioning and allocation. IMPORTANT When the SCSI ID is set using the external operator panel connector CN1, all pins listed in Table 5.1 should be open. If any of pins are shorted, unexpected SCSI ID is set. Table 5.1 SCSI ID setting (single-ended 16-bit SCSI model: MAx3xxxSP) SCSI ID MAx3xxxSP (CN7) 5-6 3-4 1-2 0 Open Open Open 1 Open Open Open 2 Open Open Short 3 Open Open Short 4 Open Short Open 5 Open Short Open 6 Open Short Short 7 Open Short Short 8 Short Open Open 9 Short Open Open 10 Short Open Short 11 Short Open Short 12 Short Short Open 13 Short Short Open 14 Short Short Short 15 (*1) Short Short Short *1 Set at factory shipment 5-6 Open Short Open Short Open Short Open Short Open Short Open Short Open Short Open Short C141-E035-02EN 5 - 7

Section	Page
Front title	1
PREFACE	6
CONTENTS	10
FIGURES	13
TABLES	15
CHAPTER 1 GENERAL DESCRIPTION	16
1.1 Standard Features	17
1.2 Hardware Structure	20
1.3 System Configuration	25
CHAPTER 2 SPECIFICATIONS	28
2.1 Hardware Specifications	28
2.1.1 Model name and part number	28
2.1.2 Function specifications	29
2.1.3 Environmental specifications	31
2.1.4 Error rate	32
2.1.5 Reliability	32
2.2 SCSI Function Specifications	34
CHAPTER 3 DATA FORMAT	36
3.1 Data Space	36
3.1.1 Cylinder configuration	36
3.1.2 Alternate spare area	40
3.1.3 Track format	41
3.1.4 Sector format	43
3.1.5 Format capacity	45
3.2 Logical Data Block Addressing	46
3.3 Defect Management	47
3.3.1 Defect list	47
3.3.2 Alternate block allocation	47
CHAPTER 4 INSTALLATION REQUIREMENTS	52
4.1 Mounting Requirements	52
4.1.1 External dimensions	52
4.1.2 Mounting	57
4.1.3 Notes on mounting	57
4.2 Power Supply Requirements	62
4.3 Connection Requirements	65
4.3.1 Single-ended 16-bit SCSI model (MAA31xxSP, MAB30xxSP, MAC30xxSP)	65
4.3.2 SCA2 type SCSI model (MAA31xxSC, MAB30xxSC, MAC30xxSC)	73
4.3.3 Cable connector requirements	75
4.3.4 External operator panel	79
CHAPTER 5 INSTALLATION	80
5.1 Notes on Handling Drives	80
5.2 Connections	82
5.3 Setting Terminals	84
5.3.1 SCSI ID setting	86
5.3.2 Each mode setting	87
5.3.3 Write protect, terminating resistor setting	88
5.3.4 Mode settings	89
5.4 Mounting Drives	90
5.4.1 Check before mounting	90
5.4.2 Mounting procedures	90
5.5 Connecting Cables	91
5.6 Confirming Operations after Installation and Preparation for use	92
5.6.1 Confirming initial operations	92
5.6.2 Checking SCSI connection	94
5.6.3 Formatting	97
5.6.4 Setting parameters	99
5.7 Dismounting Drives	103
CHAPTER 6 DIAGNOSTICS AND MAINTENANCE	104
6.1 Diagnostics	104
6.1.1 Self-diagnostics	104
6.1.2 Test programs	107
6.2 Maintenance Information	108
6.2.1 Maintenance requirements	108
6.2.2 Revision numbers	110
APPENDIX A LOCATIONS OF CONNECTORS, SETTING TERMINALS, AND TERMINATING RESISTORS	112
A.1 Locations of Connectors and Setting Terminals (MAx3xxxSC: SCA2 type 16-bit SCSI)	113
A.2 Locations of Connectors and Setting Terminals (MAx3xxxSP : single-ended type 16-bit SCSI)	114
APPENDIX B SETTING TERMINALS	116
B.1 Setting Terminals (MAx3xxxSP : Single-ended 16-bit SCSI)	117
APPENDIX C CONNECTOR SIGNAL ALLOCATION	120
C.1 SCSI Connector Signal Allocation: SCA2 type 16-bit SCSI	121
C.2 SCSI Connector Signal Allocation: single-ended type 16-bit SCSI	122
APPENDIX D MODEL NAMES AND PRODUCT NUMBERS	124
D.1 Model Names and Product Numbers	125
APPENDIX E SCSI INTERFACE FUNCTIONS	126
E.1 SCSI interface function specifications	127
Index	136
Addresses	141