Ganz Security NR8HL-2TB NR4HLNR8HL User Manual - Page 29

System Setting

Get Ganz Security NR8HL-2TB PDF manuals and user guides View all Ganz Security NR8HL-2TB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

System Setting > SENSITIVITY : Set the sensitivity level of the motion sensor to either Daytime or Nighttime. > MINIMUM BLOCKS : Set the minimum number of blocks (that will be considered an event) to Daytime or Night if a motion is detected in several blocks in the motion sensor area. > AREA SETUP : Specify the motion detection area. 3. To apply the change, click in the bottom of the screen. 4. When done, press the [EXIT] button on the remote control or click in the lower screen. The confirmation message appears and you will return to the previous menu. 9 The above options such as and and how to set the motion area may be restricted 9 depending on the specification of the connected camera. Motion Area Setup From the motion setup window, click in the right corner to display the area setup screen. Setting the motion area may differ depending on the camera model. Below is a typical setting of the motion area. 1. Click to move to the motion area setup screen. 2. If using the remote control, press the [ENTER] button to mark the current position. 3. Use the arrow buttons to move to a desired block and press [ENTER]. The area setup will begin. Then, use the arrow buttons to specify the area. Alternatively, you can use the drag-and-drop method to specify or release the area as using mouse. 4. If you select the specified area again, it will be released. 5. Press the [EXIT] button on the remote control or right-click any area to display the popup window as in the right picture. 6. From the popup window, move to and specify the and for the current channel. > CHANNEL : select a channel that you specify the sensitivity and minimum blocks for. >SENSITIVITY : 1(Low) ~ 10(High) - The higher the number is, the more higher the sensitivity level becomes. >MINIMUM BLOCKS : 1(High) ~ 10(Low) - The lower the number is, the higher the sensitivity level becomes. > DAYTIME SET : specify the time period that will be considered as daytime. > DAYTIME : specify the and for the daytime. > NIGHTTIME : specify the and for the nighttime. Images recorded in a low contrast scene such as at night cause severe noise, triggering the motion event too often. If this is the case, reduce the nighttime sensitivity to a degree. ᧮᧵

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
System Setting
> SENSITIVITY : Set the sensitivity level of the motion sensor to either Daytime or Nighttime.
> MINIMUM BLOCKS : Set the minimum number of blocks (that will be considered an event) to
Daytime or Night if a motion is detected in several blocks in the motion sensor area.
> AREA SETUP : Specify the motion detection area.
3. To apply the change, click
<APPLY>
in the bottom of the screen.
4. When done, press the
[EXIT]
button on the remote control or click
<CLOSE>
in the lower
screen. The confirmation message appears and you will return to the previous menu.
9
The above options such as
<SENSITIVITY>
and
<MINIMUM BLOCKS>
and how to set
the motion area may be restricted
9
depending on the specification of the connected camera.
Motion Area Setup
From the motion setup window, click
<AREA SETUP>
in the right corner to display the area setup
screen. Setting the motion area may differ depending on the camera model. Below is a typical
setting of the motion area.
1. Click
<AREA SETUP>
to move to the motion
area setup screen.
2. If using the remote control, press the
[ENTER]
button to mark the current position.
3. Use the arrow buttons to move to a desired block
and press
[ENTER]
. The area setup will begin.
Then, use the arrow buttons to specify the area.
Alternatively, you can use the drag-and-drop
method to specify or release the area as using
mouse.
4. If you select the specified area again, it will be
released.
5. Press the
[EXIT]
button on the remote control or
right-click any area to display the popup window
as in the right picture.
6. From the popup window, move to and specify the
<SENSITIVITY>
and
<MINIMUM BLOCKS>
for the current channel.
> CHANNEL : select a channel that you specify
the sensitivity and minimum blocks for.
>SENSITIVITY : 1(Low) ~ 10(High) - The higher
the number is, the more higher the sensitivity
level becomes.
>MINIMUM BLOCKS : 1(High) ~ 10(Low) - The
lower the number is, the higher the sensitivity level becomes.
> DAYTIME SET : specify the time period that will be considered as daytime.
> DAYTIME : specify the
<SENSITIVITY>
and
<MINIMUM BLOCKS>
for the daytime.
> NIGHTTIME : specify the
<SENSITIVITY>
and
<MINIMUM BLOCKS>
for the nighttime.
Images recorded in a low contrast scene such as at night cause severe noise, triggering the motion
event too often.
If this is the case, reduce the nighttime sensitivity to a degree.