Ganz Security NR8HL-2TB NR4HLNR8HL User Manual - Page 48

Alarm Sensor

Get Ganz Security NR8HL-2TB PDF manuals and user guides View all Ganz Security NR8HL-2TB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

System Setting Email If an event occurs, this will notify registered users of the event by email. If you do not want to receive the email, uncheck the option in . (Page 34) >ADD NEW EMAIL If you want to add a new mail recipient beside the existing ones, click this to add the recipient. >MINIMUM EMAIL FREQUENCY Adjust the minimum frequency of sending the email. For example, even if you have set the minimum frequency to one minute and another event occurs in less than one minute after the last email sending, the email for the new event will be sent one minute after. Some email servers can block the email sending if the email delivery cycle is too short, and classify it as spam. Contact your email service provider to adjust the minimum delivery cycle so that the server does not classify the email as spam. Alarm Sensor You can configure the settings of the alarm sensor and specify the operation of the sensor if an event occurs. 1. From - , select . 2. Use the [ʆʈُٙ] buttons on the remote control or use the mouse to specify the sensor input method and operation. >NAME : You can specify the name of the alarm sensor. >OPERATION : You can specify the type of the  alarm sensor. - N/O (Normal Open) : Normally the sensor is left Open. If the sensor switches to Close, an event will be triggered. - N/C (Normal Close) : Normally the sensor is left Close. If the sensor switches to Open, an event will be triggered. >LINKED CAMERA : Set the camera to sync with the alarm sensor if it is triggered. If you have set the alarm recording and the sensor detects the recording, all synchronized cameras will start alarm recording. >ALARM OUTPUT : Specify the alarm output channel if it is detected by the alarm sensor. The alarm will be output to the specified channel. >BUZZER : Specify the output of the buzzer if an alarm is detected by the alarm sensor. >VIDEO POPUP : Select to display the video popup if an alarm is detected by the alarm sensor. If there exist multiple , the video popup will be displayed in the maximum split mode. >OSD POPUP : Select to display the OSD popup message if it is detected by the alarm sensor. >EMAIL : Select to send an email if detected by the alarm sensor. 3. To apply the change, click in the bottom of the screen. 4. When done, press the [EXIT] button on the remote control or click in the lower screen. The confirmation message appears and you will return to the previous menu. ᧰᧴

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
System Setting
Email
If an event occurs, this will notify registered users of the event by email. If you do not want to receive
the email, uncheck the
<EMAIL NOTIFY>
option in
<MANAGEMENT>
. (Page 34)
>ADD NEW EMAIL
If you want to add a new mail recipient beside the
existing ones, click this to add the recipient.
>MINIMUM EMAIL FREQUENCY
Adjust the minimum frequency of sending the email.
For example, even if you have set the minimum
frequency to one minute and another event occurs
in less than one minute after the last email sending,
the email for the new event will be sent one minute
after.
Some email servers can block the email sending
if the email delivery cycle is too short, and
classify it as spam.
Contact your email service provider to adjust the minimum delivery cycle so that the server does
not classify the email as spam.
Alarm Sensor
You can configure the settings of the alarm sensor and specify the operation of the sensor if an
event occurs.
1. From
<SYSTEM SETUP> - <EVENT>
, select
<ALARM SENSOR>
.
2. Use the
[
ʆʈ
ُٙ
]
buttons on the remote control or
use the mouse to specify the sensor input method
and operation.
>NAME : You can specify the name of the alarm
sensor.
>OPERATION : You can specify the type of the
alarm sensor.
- N/O (Normal Open) : Normally the sensor is left
Open. If the sensor switches to Close, an event will be triggered.
- N/C (Normal Close) : Normally the sensor is left Close. If the sensor switches to Open,
an event will be triggered.
>LINKED CAMERA : Set the camera to sync with the alarm sensor if it is triggered.
If you have set the alarm recording and the sensor detects the recording, all synchronized
cameras will start alarm recording.
>ALARM OUTPUT : Specify the alarm output channel if it is detected by the alarm sensor.
The alarm will be output to the specified channel.
>BUZZER : Specify the output of the buzzer if an alarm is detected by the alarm sensor.
>VIDEO POPUP : Select to display the video popup if an alarm is detected by the alarm sensor.
If there exist multiple
<LINKED CAMERA>
, the video popup will be displayed in the maximum
split mode.
>OSD POPUP : Select to display the OSD popup message if it is detected by the alarm sensor.
>EMAIL : Select to send an email if detected by the alarm sensor.
3. To apply the change, click
<APPLY>
in the bottom of the screen.
4. When done, press the
[EXIT]
button on the remote control or click
<CLOSE>
in the lower
screen. The confirmation message appears and you will return to the previous menu.