Garmin zumo 220 Owner's Manual - Page 46

Changing the Fuse, Mounting on Your Dashboard, permanent

Get Garmin zumo 220 PDF manuals and user guides
UPC - 753759101657
View all Garmin zumo 220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Appendix Changing the Fuse NOTICE When replacing the fuse, do not lose any of the small pieces and make sure they are put back in the proper position. The vehicle power cable does not work unless it is assembled correctly. If your unit will not charge in your vehicle, you might need to replace the fuse located at the tip of the vehicle adapter. 1. Use a coin to push down the silver tip, and turn the coin counter-clockwise, one-quarter turn. 2. Remove the end piece, the silver tip, and the fuse. 3. Install a 1 A fast-blow fuse of the same size. End piece Silver tip 4. Ensure that the silver Fuse tip is located in the end piece. Using a coin, replace the end piece. Mounting on Your Dashboard NOTICE The permanent mounting adhesive is extremely difficult to remove after it is installed. Use the enclosed mounting disk to mount your unit to the dashboard and comply with certain state regulations. 1. Clean and dry the dashboard where you are placing the disk. 2. Remove the backing from the adhesive on the bottom of the disk. 3. Place the disk on the dashboard. 4. Remove the clear plastic cover from the top of the disk. 5. Place the suction cup mount on top of the disk. Flip the lever down (toward the disk). 42 zūmo 200 Series Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
³2
zūmo 200 Series Owner’s Manual
Appendix
Changing the Fuse
NOTICE
When replacing the fuse, do not lose any
of the small pieces and make sure they
are put back in the proper position. The
vehicle power cable does not work unless
it is assembled correctly.
If your unit will not charge in your
vehicle, you might need to replace the
fuse located at the tip of the vehicle
adapter.
1. Use a coin to push down the silver tip,
and turn the coin counter‑clockwise,
one‑quarter turn.
2. Remove the end piece, the silver tip,
and the fuse.
3. Install a 1 A fast‑blow
fuse of the same size.
4. Ensure that the silver
tip is located in the
end piece. Using a
coin, replace the end
piece.
Mounting on Your
Dashboard
NOTICE
The
permanent
mounting adhesive is
extremely difficult to remove after it is
installed.
Use the enclosed mounting disk to mount
your unit to the dashboard and comply
with certain state regulations.
1. Clean and dry the dashboard where
you are placing the disk.
2. Remove the backing from the
adhesive on the bottom of the disk.
3. Place the disk on the dashboard.
4. Remove the clear plastic cover from
the top of the disk.
5. Place the suction cup mount on top of
the disk. Flip the lever down (toward
the disk).
End
piece
Silver tip
Fuse