HP BladeSystem bc2500 Setup and Installation Guide HP BladeSystem bc2000 and b - Page 30

WARNING, CAUTION, Refer to

Get HP BladeSystem bc2500 - Blade PC PDF manuals and user guides View all HP BladeSystem bc2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

7. Screw the hexagonal washer onto the shaft of the screw until it passes all the threads and is secure within the thumbscrew housing (3). 8. Repeat steps 1 through 7 for the other thumbscrew. WARNING! Remove the two hot-plug power supplies before installing the enclosure into the rack to reduce weight. WARNING! At least two people must lift the enclosure into the rack together. If the enclosure is loaded into the rack above chest level, a third person must assist with aligning the enclosure with the rails while the other two people support the weight of the enclosure. CAUTION: Do not remove the enclosure from the rack by the thumbscrews. Use the handles located above the thumbscrews. To load the enclosure into the rack: 1. Refer to the Measuring with the Rack Template on page 17 section in this chapter. 2. Stand at the front of the rack. 3. Align the bottom of the enclosure with the top of the rack rails. 4. Slide the enclosure fully into the rack (1). 22 Chapter 4 Installing and Cabling the HP PC BladeSystem PC Blade Enclosure ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
7.
Screw the hexagonal washer onto the shaft of the screw until it passes all the threads and is secure
within the thumbscrew housing (3).
8.
Repeat steps 1 through 7 for the other thumbscrew.
WARNING!
Remove the two hot-plug power supplies before installing the enclosure into the rack
to reduce weight.
WARNING!
At least two people must lift the enclosure into the rack together. If the enclosure is
loaded into the rack above chest level, a third person must assist with aligning the enclosure with
the rails while the other two people support the weight of the enclosure.
CAUTION:
Do not remove the enclosure from the rack by the thumbscrews. Use the handles
located above the thumbscrews.
To load the enclosure into the rack:
1.
Refer to the
Measuring with the Rack Template
on page
17
section in this chapter.
2.
Stand at the front of the rack.
3.
Align the bottom of the enclosure with the top of the rack rails.
4.
Slide the enclosure fully into the rack (1).
22
Chapter 4
Installing and Cabling the HP PC BladeSystem PC Blade Enclosure
ENWW