HP BladeSystem bc2500 Setup and Installation Guide HP BladeSystem bc2000 and b - Page 40

Attaching the Diagnostic Adapter

Get HP BladeSystem bc2500 - Blade PC PDF manuals and user guides View all HP BladeSystem bc2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Attaching the Diagnostic Adapter Attach the diagnostic adapter to the diagnostic connector on the front of the blade PC to attach peripherals such as a keyboard, video, mouse, USB diskette drive, or USB optical drive. NOTE: Either a USB 2.0 or a USB 1.1 diagnostic adapter can operate with the blade PC, but the USB 1.1 diagnostic adapter does not support USB 2.0 devices. The USB 2.0 diagnostic adapter shows up under System Devices in Device Manager as "Generic Bus." To install the diagnostic adapter: 1. Power down the blade PC. For more information, see Powering Down a Blade PC on page 28. 2. Insert the diagnostic adapter into the diagnostic connector on the blade PC (1). 3. Tighten the thumbscrews securing the diagnostic adapter in place (2). Use the following figure and table to identify connectors on the USB 2.0 diagnostic adapter. 32 Chapter 4 Installing and Cabling the HP PC BladeSystem PC Blade Enclosure ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Attaching the Diagnostic Adapter
Attach the diagnostic adapter to the diagnostic connector on the front of the blade PC to attach
peripherals such as a keyboard, video, mouse, USB diskette drive, or USB optical drive.
NOTE:
Either a USB 2.0 or a USB 1.1 diagnostic adapter can operate with the blade PC, but the USB
1.1 diagnostic adapter does not support USB 2.0 devices. The USB 2.0 diagnostic adapter shows up
under System Devices in Device Manager as “Generic Bus.”
To install the diagnostic adapter:
1.
Power down the blade PC. For more information, see
Powering Down a Blade PC
on page
28
.
2.
Insert the diagnostic adapter into the diagnostic connector on the blade PC (1).
3.
Tighten the thumbscrews securing the diagnostic adapter in place (2).
Use the following figure and table to identify connectors on the USB 2.0 diagnostic adapter.
32
Chapter 4
Installing and Cabling the HP PC BladeSystem PC Blade Enclosure
ENWW