HP Cluster Platform Interconnects v2010 Gigabit Ethernet Interconnect Guide - Page 35

3.

Reset and clear buttons

4.

Self test LED

5.

Status LEDs for the fans, power supplies and switch modules

6.

LED mode select button and indicator LEDs

5.1.1 ProCurve 5308xl LEDs and Ports

To optimize the amount of information displayed for each of the switch ports, the switches use

a Mode LED for each port. The operation of this LED is controlled by the LED Mode Select button

on the switch chassis, and the current selection is indicated by the mode indicator LEDs near the

button. Press the button to change from one mode to the next.

The console port is used to connect a console to the switch by using the serial cable supplied

with the switch. The console is a full-featured interface used to configure, monitor, and

troubleshoot the switch. It runs on a PC, laptop, or handheld device emulating a terminal, or

any terminal that configures a communication protocol.

The reset button is used to reset the switch while it is powered on. This action clears any temporary

error conditions that may have occurred, executes the switch self test, and resets all network

activity counters to zero. The counters are displayed in the switch console interface, the switch

web browser interface, and through SNMP network management applications, such as HP

ProCurve Manager for Hubs & Switches.

The clear button is used for the following purposes:

•

Deleting passwords — When pressed by itself for at least one second, the Clear button deletes

any switch console access passwords that you may have configured. Use this feature if you

have misplaced the password and need console access. This button is provided for your

convenience, but its presence means that if you are concerned with the security of the switch

configuration and operation, you should make sure the switch is installed in a secure location,

such as a locked wiring closet.

•

Restoring factory default configuration — When pressed with the Reset button in a specific

pattern, the Clear button clears any configuration changes you may have made through the

switch console, the web browser interface, or SNMP management, and restores the factory

default configuration to the switch.

Table 5-1

describes the LEDs on a ProCurve 5308xl chassis.

Table 5-1 Switch Chassis LEDs

Meaning

State

LEDs

The switch is receiving power.

On

Power (green)

The switch is not receiving power.

Off

The normal state; indicates that there are no fault conditions on the

switch.

Off

Fault (orange)

A fault has occurred on the switch, one of the switch modules, an

individual port, a power supply, or a fan. The Status LED for the module

or other device with the fault will flash simultaneously.

Flashing

On briefly at the beginning of switch self test after the switch is powered

on or reset. If on for a prolonged time, the switch has encountered a

fatal hardware failure, or has failed its self test.

On

The normal operational state; the switch is not undergoing self test.

Off

Self Test (green)

The switch self test and initialization are in progress after you have

power cycled or reset the switch. The switch is not operational until this

On

LED goes off. The Self Test LED also comes on briefly when you hot

swap a module into the switch and the module is automatically self

tested.

5.1 ProCurve 5308xl Features

35

Section	Page
Gigabit Ethernet Interconnect Guide	1
Table of Contents	3
About This Manual	7
Audience	7
Organization	7
Additional Documentation	7
HP Encourages Your Comments	10
Related Documentation	10
Cluster Component Documentation	10
World-Wide Web Resources	10
Conventions	11
1 Gigabit Ethernet Solutions Overview	12
1.1 Supported Gigabit Ethernet Interconnects	12
1.2 Gigabit Ethernet Solution Possibilities	13
1.3 Gigabit Ethernet Solution Possibilities (used in older versions of HP CPxxxx)	13
1.4 High-density Configuration Solutions	14
1.5 High-density Configuration Solutions (used in older versions of HP CPxxxx)	15
1.6 Modular Configuration Solutions	16
2 HP ProCurve 2650	18
2.1 HP ProCurve 2650 Overview	18
2.2 ProCurve 2650 LEDs and Buttons	19
2.2.1 Reset Button	21
2.2.2 Clear Button	21
2.2.3 LED Diagnostics	21
3 HP ProCurve 2800 Series	23
3.1 HP ProCurve 2824 Overview	23
3.1.1 HP ProCurve 2824 Front View	23
3.1.2 HP ProCurve 2824 Rear View	24
3.2 HP ProCurve 2848 Overview	24
3.2.1 Front Panel	24
3.2.2 Rear Panel	25
3.3 HP ProCurve 2800 Series LEDs and Buttons	26
3.3.1 Reset Button	27
3.3.2 Clear Button	28
3.3.3 ProCurve 2800 Series LED Diagnostics	28
4 HP ProCurve 3500yl Series	29
4.1 HP ProCurve 3500yl-24G-PWR Overview	30
4.2 HP ProCurve 3500yl-48G-PWR Overview	31
4.3 HP ProCurve 3500yl Series LEDs	32
4.4 ProCurve Switch 10-GbE yl Module	32
4.5 Installing an HP ProCurve 3500yl Series in a Rack	33
5 HP ProCurve 5308xl	34
5.1 ProCurve 5308xl Features	34
5.1.1 ProCurve 5308xl LEDs and Ports	35
5.1.2 ProCurve 5308xl Rear View	36
5.1.3 Self Test	37
5.2 ProCurve 10/100/1000–T xl Module	38
5.3 Installing a Switch Module	39
5.4 Replacing or Removing a Switch Module	40
5.5 Installing a Second Power Supply	40
5.5.1 Installation Precautions	40
5.5.2 Installation Steps	41
5.6 Installing a ProCurve 5308xl in a Rack	43
6 HP ProCurve 5400zl Series	47
6.1 HP ProCurve 5406zl Overview	48
6.2 HP ProCurve 5412zl Overview	49
6.3 HP ProCurve Switch 5400zl 24 port Gig-T PoE Module	51
6.4 HP ProCurve 5400zl Series 4-port 10-GbE Switch Module	52
6.5 ProCurve 5400zl Series LEDs	53
6.6 Installing a ProCurve 5400zl Series in a Rack	53
6.7 Replacing a ProCurve 5400zl Series	53
7 HP ProCurve 6400cl	54
7.1 ProCurve 6400cl LEDs	55
7.2 Removing a ProCurve 6400cl from a Rack	56
8 HP ProCurve 9300 Series	57
8.1 ProCurve 9300 Series Overview	57
8.1.1 ProCurve 9304M	58
8.1.2 ProCurve 9308M	59
8.1.3 ProCurve 9315M	59
8.2 Chassis Modules	60
8.3 Installing and Removing a Module	61
8.3.1 Installing a Module	62
8.3.2 Removing a Module	63
8.3.3 Verifying the Module is Installed Correctly	63
8.3.4 Removing and Installing a mini-GBIC	64
8.4 Installing and Removing a Power Supply	65
8.4.1 Verifying Power Supply Operation	66
8.5 Installing a ProCurve 9300 Series Chassis in a Rack	67
9 Cisco Catalyst Blade Switch 3020 for HP c-Class BladeSystem	69
9.1 Replacing the Cisco Catalyst Blade Switch 3020	70
10 HP GbE2c Ethernet Blade Switch for c-Class BladeSystem	71
10.1 Replacing the GbE2c Ethernet Blade Switch	71
11 HP 1Gb Ethernet Pass-Thru Module	72
12 Troubleshooting	73
12.1 Basic Ethernet Troubleshooting Tips	73

HP Cluster Platform Interconnects v2010 Gigabit Ethernet Interconnect Guide - Page 35

ProCurve 5308xl LEDs and Ports, ProCurve Manager for Hubs & Switches.

Page 35 highlights