Home » HP Manuals » Repeaters & Transceivers » HP GbE2c » Manual Viewer

HP GbE2c HP BladeSystem c7000 Enclosure Maintenance and Service Guide - Page 33

Device bay blank, Device bay shelf

UPC - 808736802215

Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Device bay blank Remove the component as indicated. CAUTION: For best cooling practices, do not operate the enclosure for extended periods with more than one component or blank removed. When removing an active component, replace it with a blank. To replace the component, reverse the removal procedure. Device bay shelf The c7000 enclosure is divided into four quadrants by the vertical support metal work. Within each quadrant, a removable divider supports half-height blades. To install a full-height blade in any quadrant, this divider must be removed. Therefore, a quadrant can only contain either full-height blades or halfheight blades. CAUTION: Failure to install the divider in a quadrant when installing half-height blades can result in damage to the connectors on the server blades. Removal and replacement procedures 33

Section	Page
HP BladeSystem c7000 Enclosure Maintenance and Service Guide	1
Notice	2
Contents	3
Customer self repair	5
Parts only warranty service	5
Illustrated parts catalog	16
Mechanical components	16
System components	20
Front system components	20
Rear system components	23
Removal and replacement procedures	28
Required tools	28
Safety considerations	28
Preventing electrostatic discharge	28
Warning and caution messages	28
Preparing the enclosure	30
Power down the server blades or workstation blades	30
Power down the storage blades	31
Power down the enclosure	31
HP BladeSystem c7000 power supply or power supply blank	32
Device bay blank	33
Device bay shelf	33
Half-height or full-height blade	36
HP BladeSystem Insight Display	38
Fan blank	40
Active Cool 200 fan	41
Interconnect blank	41
Interconnect switch or Pass-Thru module	42
Interconnect bay dividers	43
Onboard Administrator blank	44
Onboard Administrator	44
Onboard Administrator tray	45
AC input module	46
Rear cage	47
Insight Display front-to-rear interconnect board	49
Insight Display signal pass-thru board	51
Midplane assembly	53
Cabling	55
Single-phase AC configuration	55
Three-phase AC configuration	55
HP BladeSystem c7000 Enclosure DC configuration	56
Onboard Administrator cabling	57
Onboard Administrator with KVM cabling	58
Diagnostic tools	59
Troubleshooting resources	59
Onboard Administrator	59
Server blade diagnostic tools	59
HP Insight Diagnostics	59
HP Insight Diagnostics survey functionality	59
Integrated Management Log	60
Array Diagnostic Utility	60
Component identification	61
Enclosure front components	61
Device bay numbering	61
Full-height device bay numbering	62
Half-height device bay numbering	62
Power supply LEDs	63
Power supply bay numbering	63
HP BladeSystem Insight Display	64
Insight Display overview	64
HP BladeSystem Insight Display components	65
Enclosure rear components	65
Interconnect module bay numbering	66
Onboard Administrator components	67
Onboard Administrator LEDs and buttons	68
Onboard Administrator with KVM LEDs and buttons	68
Fan bay numbering	69
Fan LED	69
Specifications	71
Environmental specifications	71
Enclosure specifications	71
Power specifications	72
DC power	72
Single-phase power	72
Three-phase power (North America/Japan)	73
Three-phase power (International)	73
Acronyms and abbreviations	74

Match case Limit results 1 per page

Removal and replacement procedures

Device bay blank

Remove the component as indicated.

CAUTION:

For best cooling practices, do not operate the enclosure for extended periods with

more than one component or blank removed. When removing an active component, replace

it with a blank.

To replace the component, reverse the removal procedure.

Device bay shelf

The c7000 enclosure is divided into four quadrants by the vertical support metal work. Within each

quadrant, a removable divider supports half-height blades. To install a full-height blade in any quadrant,

this divider must be removed. Therefore, a quadrant can only contain either full-height blades or half-

height blades.

CAUTION:

Failure to install the divider in a quadrant when installing half-height blades can

result in damage to the connectors on the server blades.