HP GbE2c HP BladeSystem c7000 Enclosure Maintenance and Service Guide - Page 52

Remove the Onboard Administrator modules Onboard Administrator

Get HP GbE2c - Blc Layer 2/3 Fiber SFP Option PDF manuals and user guides
UPC - 808736802215
View all HP GbE2c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4. Disengage and extend the following components approximately 8 cm (3 in): o Half-height and full-height blades ("Half-height or full-height blade" on page 36) o Power supplies ("HP BladeSystem c7000 power supply or power supply blank" on page 32) 5. Remove the fans ("Active Cool 200 fan" on page 41). 6. Remove the interconnect switches and Pass-Thru modules ("Interconnect switch or Pass-Thru module" on page 42). 7. Remove the Onboard Administrator modules ("Onboard Administrator" on page 44). Remove the Onboard Administrator tray ("Onboard Administrator tray" on page 45). 8. Remove the rear cage ("Rear cage" on page 47). WARNING: To reduce the risk of personal injury or equipment damage, at least two people are needed to safely move the rear cage. 9. Remove the two T-15 Torx screws that secure the pass-thru board. 10. Disconnect the pass-thru board from the cable. Removal and replacement procedures 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Removal and replacement procedures
52
4.
Disengage and extend the following components approximately 8 cm (3 in):
o
Half-height and full-height blades ("Half-height or full-height blade" on page 36)
o
Power supplies ("HP BladeSystem c7000 power supply or power supply blank" on page 32)
5.
Remove the fans ("Active Cool 200 fan" on page 41).
6.
Remove the interconnect switches and Pass-Thru modules ("Interconnect switch or Pass-Thru module"
on page 42).
7.
Remove the Onboard Administrator modules ("Onboard Administrator" on page 44).
Remove the Onboard Administrator tray ("Onboard Administrator tray" on page 45).
8.
Remove the rear cage ("Rear cage" on page 47).
WARNING:
To reduce the risk of personal injury or equipment damage, at least two people
are needed to safely move the rear cage.
9.
Remove the two T-15 Torx screws that secure the pass-thru board.
10.
Disconnect the pass-thru board from the cable.