Home » HP Manuals » Servers » HP Integrity rx8620 » Manual Viewer

HP Integrity rx8620 Installation (Smart Setup) Guide, Windows Server 2003, v6. - Page 26

Task 7: Prepare the Server Hardware for OS Installation, Set Up the Boot Drive, Boot to EFI

View all HP Integrity rx8620 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

previous installation attempt failed; however, you are not required to answer questions answered in the CIW from the previous setup attempt. • Maintenance and Troubleshooting-This option provides access to third-party maintenance and troubleshooting tools that you can use before installing the OS. Examples of these tools include system flash BIOS updates, computer diagnostic tools, and virus scanning utilities. Task 7: Prepare the Server Hardware for OS Installation Complete the following tasks to set up the server hardware for OS installation. Set Up the Boot Drive The OS installs through the boot controller detected as adapter zero to the drive detected as drive zero. CAUTION: HP strongly recommends that only the target OS drive is connected during installation. This ensures that the OS is installed on the correct drive. Make sure that the Z: drive is free because Windows Server 2003 creates the EFI partition there. To set up the boot drive, complete the following steps: 1. Power off the server. 2. Make a note listing all device connections so you can reconnect them after the installation. 3. Disconnect mass storage devices from all controllers except the boot controller. 4. Configure the boot controller and boot drive. HP recommends that you install the boot controller in the root cell. NOTE: If you are using an HP Smart Array controller, see the controller user guide for more information. You can interrupt the boot process to invoke the EFI-Based Option ROM Configuration for Arrays (ORCA). To invoke this utility: 1. Press F8 on the GUI console. 2. Press ESC 8 on the headless console. Boot to EFI To launch the EFI Shell, complete the following steps: 1. Boot the server. The server automatically goes to the EFI Boot Manager Menu. 2. Scroll down and select EFI Shell. 3. Press Enter. 4. Choose from the following: • If you are using the Enhanced EFI Boot Manager Menu (gray background), select EFI Boot Manager Menu > EFI Shell. • If you are using the Legacy EFI Boot Manager Menu (black background), select EFI Boot Manager Menu > EFI Shell [Built-in]. Locate the DVD/CD Drive When hardware (for example, HDD, a USB device, vMedia, or a DVD-ROM drive) is added to a system after it has booted to EFI, the EFI Shell environment does not detect the new device. You must reconnect the device driver for the EFI Shell to recognize the device. The EFI Shell environment creates default mappings for device handles that support a recognized file system. After you change the system configuration or add a new device, you must regenerate these mappings. To enable the EFI Shell to detect and access the DVD/CD drive, complete the following steps: 26 Preparing for the Installation

Section	Page
Installation Guide	1
Table of Contents	3
About This Document	9
Intended Audience	9
New and Changed Information in This Edition	9
Document Organization	9
Typographic Conventions	10
Related Information	10
Publishing History	11
HP Encourages Your Comments	11
1 Preparing for the Installation	13
Task 1: Determine Current System Status	13
Task 2: Verify Hardware Compatibility	13
Task 3: Back up Existing Data	14
Task 4: Choose an Installation Environment	14
Using Windows Server 2003 OS Media (Provided by Microsoft) + HP Smart Setup + Smart Update Media	15
Using HP Reinstallation Media	15
Task 5: Locate Your Microsoft Certificate of Authenticity (with Product Key)	15
Task 6: Set up an Installation Method	18
Set up a Headless Console	18
Set up a Headless Console Using a Null Modem Cable	19
Set up a Headless Console Using a LAN	19
Set up a Headless Console Using a Remote Serial Console (rx2660, rx3600, rx6600, BL860c, BL870c, rx7640, rx8640, and Superdome/sx2000 Servers Only)	19
Set up a GUI Console	20
Set up an Integrated Remote Console (rx2660, rx3600, rx6600, BL860c, BL870c, rx7640, rx8640, and Superdome/sx2000 Servers Only)	21
Set up a Virtual Media (vMedia) Drive	22
Set up PXE/WDS	22
Set up a WDS Server	23
Install WDS	24
Configure WDS	24
Authorize a WDS Server in Active Directory	25
Use the Client Installation Wizard	25
Task 7: Prepare the Server Hardware for OS Installation	26
Set Up the Boot Drive	26
Boot to EFI	26
Locate the DVD/CD Drive	26
Set ACPI Flag to Windows (Cell-Based Servers Only)	27
Set Cell Local Memory to 100% (Cell-Based Servers Only)	28
Specify the Network Interface Card for a Network Boot	28
2 Installing the OS	29
Install from a Headless Console	29
Run EBSU	30
Run Windows Setup	33
Enter the Product Key	33
Install from a GUI Console	34
Run EBSU	34
Run Windows Setup	36
Specify Server Settings	37
Install from PXE	37
Reinstall from a Headless Console	38
Load the System Image to the Boot Disk	38
Configure after the Initial Boot	39
Reinstall from a GUI Console	40
Load the System Image to the Boot Disk	40
Configure after the Initial Boot	41
Apply OS Updates Using the Smart Update Media	42
Enable Windows Components	42
Install TCP/IP	42
Install SNMP	43
Configure SNMP	43
Set IP Addresses from a Headless Console	43
Enable and Run Remote Desktop Connection	44
Update Firmware, Drivers, and Software	44
Update Firmware	44
Update Device Drivers	45
Register for HP Support Notifications	46
Register for Microsoft Security Notifications	46
Register for Microsoft Windows Update	46
Miscellaneous Installation Issues	46
Using Integrated Remote Console to Install Windows on rx2660, rx3600, rx6600, BL860c, BL870c, rx7640, rx8640, and Superdome/sx2000 Servers	46
Installing a Windows Guest on an HPVM Host	47
Enabling Hyperthreading on HP Integrity Servers	48
Enable Hyperthreading Using EFI	48
Enable Hyperthreading Using Partition Manager	49
3 Installing and Configuring the Management Tools	51
Install the Integrity Support Pack (ISP)	51
Configure System Management Homepage	54
Set Up Browser Access	55
Set Up and Change Your SMH Security Settings After Support Pack Installation	55
Initialize SMH	55
Configure the Management Agents	56
Activate and Deactivate Agents	56
Configure the Event Notifier	57
Set the SNMP Data Collection Interval	59
Monitor Server Processes	60
Send SNMP Traps to Management Applications by IP Address	61
Verify Installation of the nPartition Management Tools	62
Verify nPartition Commands	63
Verify Partition Manager Installation	63
A Preparing the Server for Microsoft SQL Server	65
SQL Server 2005 Installation	65
Install SQL Server from the Command Prompt	66
Install SQL Server from the GUI	66
B EFI Utilities	69
Introduction to EFI	69
EFI Boot Manager	69
EFI Shell	69
Common EFI Shell Commands	70
EFI-Based Setup Utility	73
Creating a Boot File Using the EFI Shell	74
Verify Successful Boot File Creation	74
C nPartitioning	77
Quick Start	77
Getting to Know nPartitions	78
Partitioning Continuum	78
Cell Structure of nPartitions	78
Properties of nPartitions	79
Cell and nPartition Boot Phases	80
Cell Boot Phase	80
nPartition Boot Phase	81
Choosing a Management Tool	81
Management Interface Options	82
IPMI	82
IPMI Block Transfer (IPMI BT)	82
IPMI over LAN	82
Managing nPartitions Using IPMI over LAN	83
Running Partition Manager Using IPMI over LAN	83
Running nPartition Commands Using IPMI over LAN	83
WBEM	83
Securing the WBEM Connection	84
Managing nPartitions Using WBEM	84
Running Partition Manager Using WBEM	85
Running nPartition Commands Using WBEM	85
Choosing a Management Mode	85
Local Management	85
Remote Management Using IPMI	86
Remote Management Using WBEM	86
Authentication and Authorization Issues	86
Local Management	86
Remote Management Using IPMI	87
Remote Management Using WBEM	87
Setting up the Management Station	88
Controlling the Management Station Remotely	88
Remote Control	88
Terminal Services	88
Remote Desktop	88
Telnet	89
Performing nPartition Management Tasks	89
Listing the Status of an nPartition or Complex	89
Using Partition Manager	89
Using nPartition Commands	89
Using the Management Processor Command Menu	90
Using the EFI Shell	90
Creating nPartitions	90
Creating the First nPartition in a Server Complex	90
Creating a Genesis Partition for a Server Complex	90
Creating Additional nPartitions in a Server Complex	90
Modifying nPartitions	91
Booting and Resetting nPartitions	92
Using the MP Command Menu	93
Using the EFI Shell	93
Using Microsoft Windows Commands	93
D SMH and Management Agents	95
HP Insight Management Agents	95
HP Insight Foundation Agents	95
HP Insight Server Agents	95
HP Insight NIC Agents	96
HP Insight Storage Agents	96
HP Insight Management Services	96
Using SMH	97
Accessing WebAgents	97
Navigating SMH	98
The SMH Home Page	98
System Status	99
Overall System Status	99
System Report	99
Network	100
Storage	100
Operating System	100
System	101
System Configuration	101
E Headless Windows Installations	103
Why Headless?	103
What is a Headless System?	103
Benefits of Headless Systems	103
How to Access a Headless System	104
Console Definitions	104
In-Band vs. Out-of-Band	104
Remote Desktop	104
Physical Aspects of Integrity Consoles	104
Management Processor	104
Emergency Management Services (EMS)	104
Firmware Redirection	105
Special Administration Console	105
Configuring Consoles	105
Management Processor Settings	105
Cellular Systems	106
Noncellular Systems	106

Match case Limit results 1 per page

previous installation attempt failed; however, you are not required to answer questions

answered in the CIW from the previous setup attempt.

•

Maintenance and Troubleshooting—This option provides access to third-party maintenance

and troubleshooting tools that you can use before installing the OS. Examples of these tools

include system flash BIOS updates, computer diagnostic tools, and virus scanning utilities.

Task 7: Prepare the Server Hardware for OS Installation

Complete the following tasks to set up the server hardware for OS installation.

Set Up the Boot Drive

The OS installs through the boot controller detected as adapter zero to the drive detected as drive

zero.

CAUTION:

HP strongly recommends that only the target OS drive is connected during

installation. This ensures that the OS is installed on the correct drive. Make sure that the Z: drive

is free because Windows Server 2003 creates the EFI partition there.

To set up the boot drive, complete the following steps:

Power off the server.

Make a note listing all device connections so you can reconnect them after the installation.

Disconnect mass storage devices from all controllers except the boot controller.

Configure the boot controller and boot drive. HP recommends that you install the boot

controller in the root cell.

NOTE:

If you are using an HP Smart Array controller, see the controller user guide for

more information. You can interrupt the boot process to invoke the EFI-Based Option ROM

Configuration for Arrays (ORCA). To invoke this utility:

Press

on the GUI console.

Press

ESC 8

on the headless console.

Boot to EFI

To launch the EFI Shell, complete the following steps:

Boot the server. The server automatically goes to the EFI Boot Manager Menu.

Scroll down and select

EFI Shell

Press

Enter

Choose from the following:

•

If you are using the Enhanced EFI Boot Manager Menu (gray background), select

EFI

Boot Manager Menu > EFI Shell

•

If you are using the Legacy EFI Boot Manager Menu (black background), select

EFI

Boot Manager Menu > EFI Shell [Built-in]

Locate the DVD/CD Drive

When hardware (for example, HDD, a USB device, vMedia, or a DVD-ROM drive) is added to

a system after it has booted to EFI, the EFI Shell environment does not detect the new device.

You must reconnect the device driver for the EFI Shell to recognize the device.

The EFI Shell environment creates default mappings for device handles that support a recognized

file system. After you change the system configuration or add a new device, you must regenerate

these mappings.

To enable the EFI Shell to detect and access the DVD/CD drive, complete the following steps:

Preparing for the Installation