HP LC2000r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 114

Refer to Opening and Closing the HP Netserver, to gain, See

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 114 highlights

Chapter 12 Troubleshooting WARNING There is a danger of explosion if the battery is incorrectly installed. For your safety, never attempt to recharge, disassemble, or burn the old battery. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. 1. Power down the HP Netserver and unplug power cord. 2. Gain access to the system board by following the appropriate instructions for removing the chassis from the rack and removing the top cover. Refer to Chapter 2, "Opening and Closing the HP Netserver," to gain access to the system board. 3. If necessary, remove the PCI board to gain access to the battery. See Figure 12-2. 4. Insert a small flat-blade screwdriver or similar tool between the battery and spring latch. See Figure 12-3. 5. Push the spring latch away from battery to release the battery. The spring contacts beneath the battery cause it to pop up allowing you to grasp the battery. 6. Remove the existing battery. 108

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 12
Troubleshooting
108
WARNING
There is a danger of explosion if the battery is incorrectly
installed. For your safety, never attempt to recharge,
disassemble, or burn the old battery. Replace only with the
same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions.
1. Power down the HP Netserver and unplug power cord.
2. Gain access to the system board by following the appropriate instructions for
removing the chassis from the rack and removing the top cover.
Refer to Chapter 2, "Opening and Closing the HP Netserver," to gain
access to the system board.
3. If necessary, remove the PCI board to gain access to the battery.
See Figure 12-2.
4. Insert a small flat-blade screwdriver or similar tool between the battery and
spring latch. See Figure 12-3.
5. Push the spring latch away from battery to release the battery.
The spring contacts beneath the battery cause it to pop up allowing you to
grasp the battery.
6. Remove the existing battery.