HP LC2000r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 42

Accessory Board Installation Guidelines, IRQ Settings, Boot Priority

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Chapter 5 Installing Additional Boards Accessory Board Installation Guidelines The following sections provide the guidelines necessary to install a PCI accessory board into the HP Netserver LP 1000r. IRQ Settings The IRQ settings are automatically assigned and don't require user intervention. The HP Netserver uses the Plug-and-Play feature of the PCI board to correctly assign its resources automatically. Boot Priority The Netserver's boot priority (BIOS search order for a boot drive) should be considered when selecting a boot device. This is especially important if you are installing a board that requires an early number in the boot order. The embedded SCSI controller consists of two channels, A and B. Channel A is used to control the internal Hot Swap SCSI drives. Channel B is used to control the external SCSI devices, including a backup tape drive. On each SCSI channel, the Netserver scans for a boot device starting at device ID 0 and works up from there. By default the Netserver searches for boot devices in this order: 1. IDE CD-ROM drive 2. Flexible disk drive 3. SCSI A channel (Hot Swap SCSI HDD) 4. SCSI B channel (external SCSI devices) 5. PCI slot P1 (32- or 64-bit slot) 6. Network connection Installing a Disk Array Controller Board Adding a disk array controller board provides additional fault tolerance to your internal or external mass storage devices. HP recommends installing the HP NetRAID-1Si, -1M, or -2M controller board in the HP Netserver LP 1000r. When installing a disk array controller board, you may alter the Netserver's boot order to allow the Netserver to boot off one of the array's drives. This boot order can be changed under the Configuration menu of the Netserver's (BIOS) Setup Utility and in the SCSI Configuration Utility. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 5
Installing Additional Boards
36
Accessory Board Installation Guidelines
The following sections provide the guidelines necessary to install a PCI accessory board
into the HP Netserver LP 1000r.
IRQ Settings
The IRQ settings are automatically assigned and don't require user intervention. The HP
Netserver uses the Plug-and-Play feature of the PCI board to correctly assign its
resources automatically.
Boot Priority
The Netserver's boot priority (BIOS search order for a boot drive) should be considered
when selecting a boot device. This is especially important if you are installing a board
that requires an early number in the boot order.
The embedded SCSI controller consists of two channels, A and B. Channel A is used to
control the internal Hot Swap SCSI drives. Channel B is used to control the external
SCSI devices, including a backup tape drive. On each SCSI channel, the Netserver scans
for a boot device starting at device ID 0 and works up from there.
By default the Netserver searches for boot devices in this order:
1. IDE CD-ROM drive
2. Flexible disk drive
3. SCSI A channel (Hot Swap SCSI HDD)
4. SCSI B channel (external SCSI devices)
5. PCI slot P1 (32- or 64-bit slot)
6. Network connection
Installing a Disk Array Controller Board
Adding a disk array controller board provides additional fault tolerance to your internal
or external mass storage devices. HP recommends installing the HP NetRAID-1Si, -1M,
or -2M controller board in the HP Netserver LP 1000r. When installing a disk array
controller board, you may alter the Netserver's boot order to allow the Netserver to boot
off one of the array's drives. This boot order can be changed under the Configuration
menu of the Netserver's (BIOS) Setup Utility and in the SCSI Configuration Utility.