HP LC2000r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 28

Closing Drive Ejector Arms, CAUTION

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Chapter 3 Installing Mass Storage Devices CAUTION To prevent snapping off the ejector arms do not apply excessive pressure. 5. Close the ejector arms by rotating each one back into place. See Figure 3-4. 6. Verify the tab on each ejector arm engages the edge of the drive bay as you close it. See Figure 3-4. Drive Ejector Arms Closing Ejector Arm Locking tab pivots when ejector arm is opened or closed. Figure 3-4. Closing Drive Ejector Arms 7. If the drive is unseated in the drive bay after closing both ejector arms, repeat this procedure from Step 2 to 5. The ejector arms may not have opened enough to engage the tab, or the SCSI connector failed to engage the SCSI connector at the rear of the Hot Swap drive bay. NOTE Closing both ejector arms will ensure the drive connector engages the electrical connector in the Hot Swap drive bay and seats the drive. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 3
Installing Mass Storage Devices
22
CAUTION
To prevent snapping off the ejector arms do not apply
excessive pressure.
5. Close the ejector arms by rotating each one back into place. See Figure 3-4.
6. Verify the tab on each ejector arm engages the edge of the drive bay as you
close it. See Figure 3-4.
Locking tab pivots
when ejector arm
is opened or closed.
Drive Ejector Arms
Closing
Ejector Arm
Figure 3-4. Closing Drive Ejector Arms
7. If
the drive is unseated in the drive bay after closing both ejector arms, repeat
this procedure from Step 2 to 5.
The ejector arms may not have opened enough to engage the tab, or the SCSI
connector failed to engage the SCSI connector at the rear of the Hot Swap
drive bay.
NOTE
Closing both ejector arms will ensure the drive connector
engages the electrical connector in the Hot Swap drive bay and
seats the drive.