HP LC2000r HP Netserver LP 1000r (1.13, 1.26 & 1.40 GHz) User Guide - Page 38

WARNING, DIMM Insertion

Get HP LC2000r - NetServer - 128 MB RAM PDF manuals and user guides View all HP LC2000r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Chapter 4 Installing Additional Memory WARNING Ensure you hold the DIMM tightly as you push it into the slot. It is possible to turn or bend the DIMM slightly while inserting it, which would damage or break the DIMM socket. If a DIMM socket is damaged, you must use another DIMM slot or replace the entire HP Netserver, since this Netserver is not repairable in the field. 11. Holding the DIMM at approximately 30° to the system board, press the DIMM fully into the slot until the retaining latches close. See Figure 4-4. If the latches do not close, the DIMM is not inserted correctly. NOTE The system board is shown removed from the Netserver for clarity. DIMM 0 Slots 1 2 3 System Board Figure 4-4. DIMM Insertion 12. Repeat Steps 7-11 to install all of the DIMMs for your memory configuration. 13. If you have completed the DIMM installation, close the Netserver and return it to the rack where power can be applied. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
Chapter 4
Installing Additional Memory
32
WARNING
Ensure you hold the DIMM tightly as you push it into the slot.
It is possible to turn or bend the DIMM slightly while
inserting it, which would damage or break the DIMM socket.
If a DIMM socket is damaged, you must use another DIMM
slot or replace the entire HP Netserver, since this Netserver is
not repairable in the field.
11. Holding the DIMM at approximately 30
°
to the system board, press the DIMM fully
into the slot until the retaining latches close. See Figure 4-4.
If the latches do not close, the DIMM is not inserted correctly.
NOTE
The system board is shown removed from the Netserver for
clarity.
0
1
2
3
DIMM
Slots
System
Board
Figure 4-4. DIMM Insertion
12. Repeat Steps 7-11 to install all of the DIMMs for your memory configuration.
13. If you have completed the DIMM installation, close the Netserver and return it to the
rack where power can be applied.