Home » HP Manuals » Laser Printers » HP LaserJet 6p/mp » Manual Viewer

HP LaserJet 6p/mp Service Manual - Page 59

DC power distribution, Overcurrent/overvoltage protection, SleepMode, High voltage power distribution

Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Note DC power distribution The DC power distribution circuitry, located on the DC Controller PCA, distributes +5 V DC and +12 V DC as follows: +5 V DC +12 V DC: +12 VA DC l Formatter PCA l Photosensors l DC Controller Circuitry l Laser/Beam Detect Circuitry l Motor l Scanner Motor l Solenoid l High Voltage Power Supply Overcurrent/overvoltage protection There are two overvoltage/overcurrent devices in this printer: l Fuse F101 provides overcurrent protection for the fusing system circuitry. To check or replace the fuse requires the removal of the DC Controller. Fuse 102 (found only on 110V units) provides overcurrent protection to the printer DC power supply circuitry. l In addition, the +12V DC and +5V DC power circuitry contains an overcurrent protection circuit that automatically shuts off the output voltage when an overcurrent condition occurs due to a short or abnormal voltage on the load side. SleepMode Instead of a power switch, the printer has a SleepMode function. After the printer has been idle for 15 minutes, it turns itself off by shifting to SleepMode. The Control Panel lights remain off, and the printer retains all printer settings and downloaded fonts and macros while in SleepMode. The printer exits SleepMode and all of the lights power on when any of the following occur: l A job is received. l The Control Panel Button is pressed. l The printer front door is opened. The printer will not enter SleepMode if there is a printer error. High voltage power distribution The High Voltage Power Supply PCA applies an overlap of DC and AC voltage to the primary charging roller and the developing roller. This circuit also applies a positive or negative DC voltage to the transfer charging roller according to the instructions from the CPU on the DC Controller PCA. This circuit also controls the image density by changing the primary AC voltage and the developing AC bias according to the setting of the print density dial. High voltage is disabled when the printer's EP Door is open (i.e., switch SW101 is open). EN DC Controller/power system 57

Section	Page
Contents	7
Figures	11
Tables	13
Product information	15
Chapter contents	15
Printer features	16
Identification	17
HP LaserJet 6L Gold	17
Model and serial	17
Specifications	20
Product overview	21
Service approach	24
Parts Exchange Program	24
Ordering parts	24
Ordering related documentation	24
Contacting HP to place an order	24
Technical assistance	25
HPCustomer Care	25
HP worldwide sales and service offices	27
Warranty	30
Hardware service during the warranty period	30
Hardware service after the warranty period	30
HP LaserJet Toner Cartridge warranty	31
Voltage conversions	31
Site requirements	33
Chapter contents	33
Site requirements	34
Operating environment	34
Printer space requirements	35
The HP C3906A/F Toner Cartridge	36
Storage conditions	36
Storing opened toner cartridges	36
Toner cartridge handling suggestions	37
Operating overview	39
Chapter contents	39
Using the Control Panel	40
Control Panel layout	40
Indicator lights	40
The Control Panel Button	42
Printing a self-test page	43
Continuous self test	46
Printing an engine test	46
Resetting the printer	47
To reset the printer	47
Printer maintenance	49
Chapter contents	49
Life expectancy of consumables	50
Toner cartridge life	51
Saving toner with EconoMode	51
Refilled toner cartridges	52
Recycling toner cartridges	52
Cleaning the printer	53
Cleaning printer components	53
Cleaning spilled toner	54
Functional overview	55
Chapter contents	55
Basic printer functions	56
DC Controller/power system	57
Print engine control system	58
Power system (on DC Controller PCA)	58
Formatter system	60
CPU	60
Read only memory (ROM)	60
Random access memory (RAM)	60
Parallel interface	60
Control Panel	60
Resolution Enhancement technology (REt)	61
EconoMode	61
Memory Enhancement technology (MEt)	61
Enhanced I/O	61
Page Protect	62
PJL overview	62
Image formation system	63
Toner cartridge	63
Step 1: Drum cleaning	64
Step 2: Drum conditioning	64
Step 3: Image writing	64
Step 4: Image developing	64
Step 5: Image transferring	64
Step 6: Image fusing	64
Paper feed system	65
Paper jam detection	67
Basic sequence of operation	68
Removal and replacement	71
Chapter contents	71
Removal and replacement strategy	72
Required tools	73
Installing memory cards (DRAM)	74
Covers and doors	75
Back Cover	75
EP Door Assembly	77
Memory Door	78
Main Cover and Paper Input Assembly	79
Internal assemblies	80
Control Panel	80
Exit Roller Assembly	81
Delivery Assembly	82
Fuser Pressure Plate	84
Heating Element	86
Pressure Roller	89
Face-Up/Face-Down Lever	90
Fuser Exit Roller Assembly	91
Paper Exit Sensor Flag	92
Top assemblies	93
Laser/Scanner Assembly	93
Solenoid	94
Pickup Roller Assembly	96
Paper Feed Frame	99
Transfer Roller Guide and Transfer Roller	103
Kick Plate	104
Separation Pad	106
Subpads	107
Feed Assembly	108
Bottom assemblies	111
Memory Door Guide	111
Motor	112
DC Controller	113
Formatter PCA	116
Troubleshooting	117
Chapter contents	117
General troubleshooting flowchart	118
Paper path and components	120
DC Controller diagram	121
Printer error troubleshooting	122
Priority of errors	122
Printer status messages	123
Service and error messages	125
Image formation troubleshooting	128
Check the toner cartridge	128
Image defect examples	129
Troubleshooting checks	135
Engine test	135
Half self-test functional check	136
Drum rotation functional check	136
High-voltage power supply check	137
Paper curl	139
Troubleshooting tools	140
Paper path check	140
Repetitive image defect ruler	141
Main wiring diagram	142
Parts and diagrams	145
Chapter contents	145
How to use the part lists and diagrams	146
Ordering parts	146
Ordering consumables	146
Accessories and supplies	147
Common hardware	148
Parts diagrams	149
Parts index	169
Alphabetical parts list	169
Numerical parts list	174
Regulatory information	179
Laser Safety (U.S.)	179
Laser Statement (Finland)	180
Toner safety	181
Ozone emission	181
FCC Statement (Class B)	182
VCCI Statement (Japan)	182

Match case Limit results 1 per page

DC Controller/power system

DC power distribution

The DC power distribution circuitry, located on the DC Controller PCA, distributes +5 V DC and +12

V DC as follows:

Overcurrent/overvoltage protection

There are two overvoltage/overcurrent devices in this printer:

Fuse F101 provides overcurrent protection for the fusing system circuitry. To check or replace the

fuse requires the removal of the DC Controller. Fuse 102 (found only on 110V units) provides

overcurrent protection to the printer DC power supply circuitry.

In addition, the +12V DC and +5V DC power circuitry contains an overcurrent protection circuit

that automatically shuts off the output voltage when an overcurrent condition occurs due to a

short or abnormal voltage on the load side.

SleepMode

Instead of a power switch, the printer has a SleepMode function. After the printer has been idle for 15

minutes, it turns itself off by shifting to SleepMode. The Control Panel lights remain off, and the

printer retains all printer settings and downloaded fonts and macros while in SleepMode.

The printer exits SleepMode and all of the lights power on when any of the following occur:

A job is received.

The Control Panel Button is pressed.

The printer front door is opened.

Note

The printer will not enter SleepMode if there is a printer error.

High voltage power distribution

The High Voltage Power Supply PCA applies an overlap of DC and AC voltage to the primary

charging roller and the developing roller. This circuit also applies a positive or negative DC voltage to

the transfer charging roller according to the instructions from the CPU on the DC Controller PCA.

This circuit also controls the image density by changing the primary AC voltage and the developing

AC bias according to the setting of the print density dial.

High voltage is disabled when the printer’s EP Door is open (i.e., switch SW101 is open).

+5 V DC

Formatter PCA

Photosensors

DC Controller Circuitry

Laser/Beam Detect Circuitry

+12 V DC:

Motor

Scanner Motor

Solenoid

+12 VA DC

High Voltage Power Supply