HP Pavilion m4-1000 HP Pavilion m4 Notebook PC Maintenance and Service Guide - Page 66

Power connector cable, and then remove the following components

Get HP Pavilion m4-1000 PDF manuals and user guides View all HP Pavilion m4-1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

11. Lift the right side of the system board (1) until it rests at an angle. 12. Remove the system board by sliding it up and to the right an angle (2). Reverse this procedure to install the system board. Power connector cable Description Power connector cable Spare part number 718429-001 Before removing the power connector cable, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the battery (see Battery on page 30) and then remove the following components: a. Hard drive (see Hard drive on page 31) b. WLAN module (see WLAN module on page 33) c. Solid-state drive (see Solid-state drive on page 35) d. Memory module service cover (see Memory module on page 36) e. Optical drive (see Optical drive on page 38) 58 Chapter 6 Removal and replacement procedures for Authorized Service Provider parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
11.
Lift the right side of the system board
(1)
until it rests at an angle.
12.
Remove the system board by sliding it up and to the right an angle
(2)
.
Reverse this procedure to install the system board.
Power connector cable
Description
Spare part number
Power connector cable
718429-001
Before removing the power connector cable, follow these steps:
1.
Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the battery (see
Battery
on page
30
) and then remove the following components:
a.
Hard drive (see
Hard drive
on page
31
)
b.
WLAN module (see
WLAN module
on page
33
)
c.
Solid-state drive (see
Solid-state drive
on page
35
)
d.
Memory module service cover (see
Memory module
on page
36
)
e.
Optical drive (see
Optical drive
on page
38
)
58
Chapter 6
Removal and replacement procedures for Authorized Service Provider parts