HP ProBook 4535s HP ProBook 4535s Notebook PC - Maintenance and Service Guide - Page 54

from each side of the hard, Rotate the hard drive upward and remove it from the bracket

Get HP ProBook 4535s PDF manuals and user guides View all HP ProBook 4535s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

4. Remove the hard drive (3) from the hard drive bay. 5. If it is necessary to replace the hard drive bracket, remove the tape (1) that secures the Mylar cover down onto the bracket, and then lift to open the Mylar cover (2). 6. Remove the two Phillips PM3.0×3.0 hard drive bracket screws (3) from each side of the hard drive (4 total screws). 7. Rotate the hard drive upward and remove it from the bracket (4). Reverse this procedure to reassemble and install the hard drive. 46 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
4.
Remove the hard drive
(3)
from the hard drive bay.
5.
If it is necessary to replace the hard drive bracket, remove the tape
(1)
that secures the Mylar
cover down onto the bracket, and then lift to open the Mylar cover
(2)
.
6.
Remove the two Phillips PM3.0×3.0 hard drive bracket screws
(3)
from each side of the hard
drive (4 total screws).
7.
Rotate the hard drive upward and remove it from the bracket
(4)
.
Reverse this procedure to reassemble and install the hard drive.
46
Chapter 4
Removal and replacement procedures