Home » HP Manuals » Storage Devices » HP StorageWorks P2000 » Manual Viewer

HP StorageWorks P2000 HP StorageWorks P2000 G3 MSA System CLI Reference Guide - Page 134

set network-parameters, Optional. An IP subnet mask for the port.

View all HP StorageWorks P2000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 134 highlights

set network-parameters Description Sets IP values for controller module network ports. IP values can be set dynamically using Dynamic Host Configuration Protocol (DHCP) for both controllers, or manually (statically) for each controller. If DHCP is enabled, manually setting an IP value for either controller disables DHCP for both controllers. Syntax To set both controllers' IP values dynamically: set network-parameters dhcp To set a controller's IP values manually: set network-parameters [ip address] [netmask netmask] [gateway gateway] controller a|b Parameters dhcp Specifies to use DHCP to set both controllers' IP values. ip address Optional. An IP address for the port. netmask netmask Optional. An IP subnet mask for the port. gateway gateway Optional. A gateway IP address for the port. controller a|b Specifies whether to apply the settings to controller A or B. Example Use DHCP to set network port IP values: # set network-parameters dhcp Success: Command completed successfully. - Network parameters were changed. Manually set network port IP values for controller A (disabling DHCP for both controllers, if it was enabled): # set network-parameters ip 192.168.0.10 netmask 255.255.255.0 gateway 192.168.0.1 controller a Success: Command completed successfully. - Network parameters were changed. See also • show network-parameters 134

Section	Page
Contents	3
Tables	7
About this guide	9
Intended audience	9
Prerequisites	9
Related documentation	9
Document conventions and symbols	10
HP technical support	10
Product warranties	10
Subscription service	11
HP web sites	11
Documentation feedback	11
Using the CLI	13
Accessing the CLI	13
CLI output modes	13
Using CLI interactively	14
Using CLI scripts	14
Using the XML API	15
Scripting guidelines	16
XML API examples	17
XML API DTD content	19
XML API basetypes	20
XML API optimization	20
Command syntax	22
Keywords and parameters	22
Disks	22
Vdisks	22
Volumes	22
Ports	22
Command completion, editing, and history	23
Viewing help	23
Size representations	24
Event log	24
Categorical list of commands	25
Alphabetical list of commands	29
abort replication	30
abort scrub vdisk	31
abort verify vdisk	32
abort volumecopy	33
add replication-volume	34
clear cache	36
clear disk-metadata	37
clear events	38
clear expander-status	39
convert master-to-std	40
convert std-to-master	41
create chap-record	42
create host	43
create master-volume	44
create remote-system	46
create replication-set	47
create schedule	50
create snap-pool	52
create snapshots	53
create task	54
create user	57
create vdisk	59
create volume	61
create volume-copy	63
create volume-set	64
delete all-master-volumes	66
delete all-snapshots	67
delete chap-records	68
delete global-spare	69
delete host	70
delete master-volume	71
delete remote-system	72
delete replication-set	73
delete schedule	74
delete snap-pool	75
delete snapshot	76
delete snapshot-write-data	77
delete task	78
delete user	79
delete vdisks	80
delete vdisk-spare	81
delete volumes	82
dequarantine	83
detach replication-volume	84
exit	86
expand master-volume	87
expand snap-pool	88
expand vdisk	89
expand volume	90
export snapshot	91
map volume	92
meta	94
ping	95
reattach replication-volume	96
remote	97
remove replication-volume	98
replicate snapshot	99
replicate volume	100
rescan	101
reset host-link	102
reset snapshot	103
restart	104
restore defaults	105
resume replication	106
rollback master-volume	107
scrub vdisk	108
set advanced-settings	109
set auto-write-through-trigger	112
set awt	113
set cache-parameters	114
Cache write policy	115
Cache optimization mode	115
Cache read-ahead size	115
set chap-record	116
set cli-parameters	117
set controller-date	120
set debug-log-parameters	121
set disk-parameters	122
set email-parameters	123
set enclosure	124
set expander-fault-isolation	125
set expander-phy	126
set host-name	127
set host-parameters	128
set iscsi-parameters	131
set job-parameters	132
set led	133
set network-parameters	134
set ntp-parameters	135
set password	136
set priorities	137
set prompt	138
set protocols	139
set remote-system	140
set replication-external-view	141
set replication-volume-parameters	142
set schedule	144
set snap-pool-policy	145
set snap-pool-threshold	146
set snmp-parameters	147
set spares	148
set system	149
set task	150
set user	152
set vdisk	154
set volume	155
show advanced-settings	156
show auto-write-through-trigger	158
show awt	158
show cache-parameters	159
show chap-records	161
show cli-parameters	162
show configuration	164
show controller-date	165
show controllers	166
show debug-log-parameters	168
show disk-parameters	169
show disks	170
show email-parameters	172
show enclosure-status	173
show enclosures	175
show events	176
show expander-status	178
show frus	180
show host-maps	182
show host-parameters	184
show hosts	186
show inquiry	187
show iscsi-parameters	188
show job-parameters	189
show license	190
show master-volumes	191
show network-parameters	193
show ntp-status	194
show ports	195
show power-supplies	197
show priorities	198
show protocols	199
show redundancy-mode	200
show refresh-counters	201
show remote-systems	202
show replication-images	203
show replication-sets	205
show replication-volumes	208
show sas-link-health	210
show schedule-details	211
show schedules	212
show sensor-status	213
show shutdown-status	215
show snap-pools	216
show snapshots	217
show snmp-parameters	219
show system	220
show system-parameters	221
show task-details	222
show tasks	226
show users	231
show vdisks	232
show versions	234
show volume-maps	235
show volumecopy-status	237
show volumes	238
shutdown	240
stty	241
suspend replication	242
test	243
trust	244
unmap volume	245
verify remote-link	246
verify vdisk	247
versions	248
volumecopy	249
Glossary	251